參數資料
型號： AD6426XB
廠商： Analog Devices, Inc.
英文描述： DIODE, RECTIFIER, DO-201AD, AXIAL LEAD, STANDARD RECOVERY, 400 V, 3 A
中文描述： 增強型手機處理器
文件頁數： 20/50頁
文件大?。?/td> 506K
代理商： AD6426XB
Preliminary Technical Information
AD6426
This Information applies to a product under development. Its characteristics and specifications are subject to change without notice. Analog Devices assumes no
obligation regarding future manufacture unless otherwise agreed to in writing. No responsibility is assumed by Analog Devices for its use; nor for any
infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent
rights of Analog Devices.
Revision Preliminary 2.3 (June 9, ′98)
- 20 -
Confidential Information
Serial Display Interface
The serial display interface is compatible with display drivers
by Motorola and Seiko-Epson. The display driver by Motorola
uses an SPI serial bus which requires an inverted or delayed
clock in comparison to the Seiko-Epson type display driver.
In the Motorola mode the data is delayed by one half clock
cycle such that the data is driven on the rising edge of SCLK
instead of on the falling edge.
The serial display interface consists of four pins; a serial data
output (DISPD0), clock (DISPCLK), chip enable (DISPEN)
and address (DISPA0). These pins are multiplexed with
GPIO4, GPIO3, LCDCTL and DISPLAYCS.
Bit 1 (DISP) of the MEMIF H8 Peripheral Control Register 80
controls the configuration of the display interface. With this
set to 0, the parallel display interface is used. Setting this bit
to one enables the use of the serial display interface. This bit
is set to 0 on reset.
Bit 4 (SERDISP MODE) of the SERDISPLAY/NMI H8
Peripheral Control Register 106 controls the serial display
mode. The default setting is Seiko-Epson mode. To enable the
Motorola mode the user must set the register bit to ONE.
Display Reset
No dedicated pin is used to reset the display sub system. It is
recommended that the VBCRESET pin is used for this
function by connecting the Reset input on the display and the
Reset input on the VBC to the AD6426 VBCRESET pin. The
VBC and display cannot be reset independently. However one
of the GPIO pins can be used to reset the display separately.
Battery ID Interface
The AD6426 provides a single-wire interface compatible with
the Dallas Semiconductor
DS2434or DS2435 Battery
Identification chip. The communication protocol supports three
operations: RESET, READ and WRITE. These operations
permit reading the present status off the battery and writing
updated information to the ID chip. The interface is available
as the BATID function multiplexed on the GPIO5 pin.
Bit 3 (DALLAS EN) of the MEMIF H8 Peripheral Control
Register 80 controls the enabling of the battery ID interface
module. Setting this bit to zero enables the interface, resetting
the bit disables it. This bit is set to one on reset.
EVBC Interface
The AD6426 interfaces directly to the Enhanced Voiceband
Baseband Converter AD6425 through the pins shown in
Table
12
.The communication is performed through three serial ports:
the Auxiliary Serial Port (ASPORT), the Baseband Serial Port
(BSPORT) and the Voiceband Serial Port (VSPORT). Layer 1
software enables/disables the clock output in order to reduce
system power consumption to a minimum if operation of the
AD6425 is not required. Figure 6 shows the interface between
the AD6426 and the AD6425 as well as to the AD6432 IF
chip.
Table 12. EVBC Interface
Name
I/O
Function
CLKOUT
EVBCRESET
O
O
Clock Output to EVBC
Reset Output to EVBC
ASPORT
ASDO
ASOFS
ASCLK
ASDI
O
O
O
I
Data Output
Output Framing Signal
Clock Output
Data Input
BSPORT
BSDO
BSOFS
BSCLK
BSIFS
BSDI
O
O
I
I
I
Data Output
Output Framing Signal
Clock Input
Input Framing Signal
Data Input
VSPORT
VSDO
VSDI
VSCLK
VSFS
O
I
I
I
Data Output
Data Input
Clock Input
Input/Output Framing Signal
相關PDF資料
PDF描述
AD6426XST 1N5817 DIODE SCHOTTKY 20V 1A DO-41
AD642J Precision, Low Cost Dual BiFET Op Amp
AD642K SCHOTTKY DIODE DO-204AL 40V 1A
AD642L Precision, Low Cost Dual BiFET Op Amp
AD642S Precision, Low Cost Dual BiFET Op Amp
相關代理商/技術參數
參數描述
AD6426XST 制造商:AD 制造商全稱:Analog Devices 功能描述:Enhanced GSM Processor
AD642J 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision, Low Cost Dual BiFET Op Amp
AD642JH 制造商:Rochester Electronics LLC 功能描述:PRECISION DUAL OP AMP IC - Bulk
AD642K 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision, Low Cost Dual BiFET Op Amp
AD642KH 制造商:Rochester Electronics LLC 功能描述:PRECISION DUAL OP AMP IC - Bulk 制造商:Analog Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*