- 您現在的位置：買賣IC網 > PDF目錄9797 > AD670JP (Analog Devices Inc)IC ADC 8BIT SGNL COND 20-PLCC PDF資料下載
參數資料
| 型號： | AD670JP |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 8BIT SGNL COND 20-PLCC |
| 產品變化通告： | Product Discontinuance 27/Oct/2011 |
| 標準包裝： | 1 |
| 位數： | 8 |
| 采樣率（每秒）： | 10k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 450mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-LCC（J 形引線） |
| 供應商設備封裝： | 20-PLCC（9x9） |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
AD670
REV. A
–7–
Table III. AD670 TIMING SPECIFICATIONS
@ +25 C
Symbol
Parameter
Min
Typ
Max
Units
WRITE/CONVERT START MODE
tW
Write/Start Pulse Width
300
ns
tDS
Input Data Setup Time
200
ns
tDH
Input Data Hold
10
ns
tRWC
Read/Write Setup Before Control
0
ns
tDC
Delay to Convert Start
700
ns
tC
Conversion Time
10
s
READ MODE
tR
Read Time
250
ns
tSD
Delay from Status Low to Data Read
250
ns
tTD
Bus Access Time
200
250
ns
tDH
Data Hold Time
25
ns
tDT
Output Float Delay
150
ns
tRT
R/W before CE or CS low
0
ns
Boldface indicates parameters tested 100% unless otherwise noted. See Specifications page for explanation.
6b. Bipolar
6c. Full Scale (Unipolar)
Figure 6. Transfer Curves
CONTROL AND TIMING OF THE AD670
Control Logic
The AD670 contains on-chip logic to provide conversion and
data read operations from signals commonly available in micro-
processor systems. Figure 7 shows the internal logic circuitry of
the AD670. The control signals, CE, CS, and R/W control the
operation of the converter. The read or write function is deter-
mined by R/W when both CS and CE are low as shown in
Table II. If all three control inputs are held low longer than the
conversion time, the device will continuously convert until one
input, CE, CS, or R/W is brought high. The relative timing of
these signals is discussed later in this section.
Figure 7. Control Logic Block Diagram
Table II. AD670 Control Signal Truth Table
R/W
CS
CE
OPERATION
0
WRITE/CONVERT
1
0
READ
X
1
NONE
X
1
X
NONE
Timing
The AD670 is easily interfaced to a variety of microprocessors
and other digital systems. The following discussion of the timing
requirements of the AD670 control signals will provide the de-
signer with useful insight into the operation of the device.
Write/Convert Start Cycle
Figure 8 shows a complete timing diagram for the write/convert
start cycle. CS (chip select) and CE (chip enable) are active low
and are interchangeable signals. Both CS and CE must be low
for the converter to read or start a conversion. The minimum
pulse width, tW, on either CS or CE is 300 ns to start a
conversion.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3100E32-7S | CONN RCPT 35POS WALL MNT W/SCKT |
| VI-23K-IU-F1 | CONVERTER MOD DC/DC 40V 200W |
| MAX3222EEAP+T | IC TXRX RS-232 LP 20-SSOP |
| VI-23J-IU-F4 | CONVERTER MOD DC/DC 36V 200W |
| VI-23J-IU-F2 | CONVERTER MOD DC/DC 36V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD670JP-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 8-bit Parallel 20-Pin PLCC T/R |
| AD670JP-REEL7 | 制造商:Analog Devices 功能描述: |
| AD670JPZ | 功能描述:IC ADC 8BIT SIGNAL COND 20-PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD670JPZ-REEL7 | 功能描述:IC ADC 8BIT SIGNAL COND 20-PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD670KN | 制造商:Analog Devices 功能描述:ADC Single SAR 8-bit Parallel 20-Pin PDIP N 制造商:Rochester Electronics LLC 功能描述:IC - 8-BIT A/D CONVERTER - Bulk |
發布緊急采購，3分鐘左右您將得到回復。