- 您現在的位置：買賣IC網 > PDF目錄10035 > AD676AD (Analog Devices Inc)IC ADC 16BIT SAMPLING 28-CDIP PDF資料下載
參數資料
| 型號： | AD676AD |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/16頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT SAMPLING 28-CDIP |
| 標準包裝： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 100k |
| 數據接口： | 并聯 |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 480mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 28-CDIP（0.605"，15.37mm） |
| 供應商設備封裝： | 28-CDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個單端，雙極 |
| 配用： | AD676-EB-ND - BOARD EVAL SAMPLING ADC AD676 |
AD676
REV. A
–14–
MICROPROCESSOR INTERFACE
The AD676 is ideally suited for use in both traditional dc mea-
surement applications supporting a microprocessor, and in ac
signal processing applications interfacing to a digital signal pro-
cessor. The AD676 is designed to interface with a 16-bit data
bus, providing all output data bits in a single read cycle. A vari-
ety of external buffers, such as 74HC541, can be used with the
AD676 to provide 3-state outputs, high driving capability, and
to prevent bus noise from coupling into the ADC. The following
sections illustrate the use of the AD676 with a representative
digital signal processor and microprocessor. These circuits pro-
vide general interface practices which are applicable to other
processor choices.
ADSP-2101
Figure 10a shows the AD676 interfaced to the ADSP-2101 DSP
processor. The AD676 buffers are mapped in the ADSP-2101’s
memory space, requiring one wait state when using a 12.5 MHz
processor clock.
The falling edge of BUSY interrupts the processor, indicating
that new data is ready. The ADSP-2101 automatically jumps to
the appropriate service routine with minimal overhead. The in-
terrupt routine then instructs the processor to read the new data
using a memory read instruction.
A0
A13
D8 – D23
ADSP-2101
IRQ2
RD
DMS
DECODER
CS
ADDRESS BUS
Y1 – Y8
A1 – A3
74HC541
G1
G2
Y1 – Y8
A1 – A3
74HC541
G1
G2
BUSY
BIT 1 – BIT 16
AD676
16
8
16
8
Figure 10a.
Figure 10b shows circuitry which would be included by a typical
address decoder for the output buffers. In this case, a data
memory access to any address in the range 3000H to 37FFH
will result in the output buffers being enabled.
The AD676 CLK and SAMPLE can be generated by dividing
down the system clock as described earlier (Figure 3), or if the
ADSP-2101 serial port clocks are not being used, they can be
programmed to generate CLK and SAMPLE.
A13
A12
A11
DMS
CS
Figure 10b.
80286
The 80286 16-bit microprocessor can be interfaced to a buff-
ered AD676 without any generation of wait states. As seen in
Figure 11, BUSY can be used both to control the AD676 clock
and to alert the processor when new data is ready. In the system
shown, the 80286 should be configured in an edge triggered, di-
rect interrupt mode (integrated controller provides the interrupt
vector). Since the 80286 does not latch interrupt signals, the in-
terrupt needs to be internally acknowledged before BUSY goes
HIGH again during the next AD676 conversion (BUSY = 0).
Depending on whether the AD676 buffers are mapped into
memory or 1/0 space, the interrupt service routine will read the
data by using either the MOV or the IN instruction. To be able
to read all the 16 bits at once, and thereby increase the 80286’s
efficiency, the buffers should be located at an even address.
AD0 – AD15
ALE
CLKOUT
INT 0
80286
RD
PCSO – 6
S2
DECODER
CS
16
Y1 – Y8
A1 – A8
74HC541
G1
G2
Y1 – Y8
A1 – A8
74HC541
G1
G2
8
DIVIDER
D
CLR
Q
D
CLR
Q
74HC04
74HC74
BIT1 – BIT16
SAMPLE
CLK
BUSY
AD676
2MHz
16
8
Figure 11.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27467T19F32SA | CONN PLUG 32POS STRAIGHT W/SCKT |
| VI-25B-MX-F1 | CONVERTER MOD DC/DC 95V 75W |
| LTC487ISW#TRPBF | IC DVR RS485 LOW PWR QUAD 16SOIC |
| MS27466T15B35P | CONN RCPT 37POS WALL MNT W/PINS |
| MS27467T19B32SC | CONN PLUG 32POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD676BD | 功能描述:IC ADC 16BIT SAMPLING 28-CDIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極 |
| AD676-EB | 功能描述:BOARD EVAL SAMPLING ADC AD676 RoHS:否 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| AD676JD | 功能描述:IC ADC 16BIT SAMPLING 28-CDIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD676JDZ | 功能描述:IC ADC 16BIT SAMPLING 28-CDIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD676JDZ# | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。