參數資料
型號: AD7193BCPZ-RL7
廠商: Analog Devices Inc
文件頁數: 32/57頁
文件大?。?/td> 0K
描述: IC ADC 24BIT SPI 4.8KHZ 32LFCSP
標準包裝: 1,500
位數: 24
采樣率(每秒): 4.8k
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
電壓電源: 模擬和數字
工作溫度: -40°C ~ 105°C
安裝類型: 表面貼裝
封裝/外殼: 32-WFQFN 裸露焊盤,CSP
供應商設備封裝: 32-LFCSP-WQ(5x5)
包裝: 帶卷 (TR)
輸入數目和類型: 4 個差分,單極;4 個差分,雙極;8 個偽差分,單極;8 個偽差分,雙極
Data Sheet
AD7193
Rev. D | Page 37 of 56
Continuous Read
Rather than write to the communications register each time a
conversion is complete to access the data, the AD7193 can be
configured so that the conversions are placed on the DOUT/
RDY line automatically. By writing 01011100 to the communi-
cations register, the user need only apply the appropriate number
of SCLK cycles to the ADC, and the conversion word is auto-
matically placed on the DOUT/RDY line when a conversion is
complete. The ADC should be configured for continuous
conversion mode.
When DOUT/RDY goes low to indicate the end of a conversion,
sufficient SCLK cycles must be applied to the ADC; the data
conversion is then placed on the DOUT/RDY line. When the
conversion is read, DOUT/RDY returns high until the next
conversion is available. In this mode, the data can be read only
once. The user must also ensure that the data-word is read
before the next conversion is complete. If the user has not read
the conversion before the completion of the next conversion, or
if insufficient serial clocks are applied to the AD7193 to read
the word, the serial output register is reset when the next
conversion is complete, and the new conversion is placed in the
output serial register.
To exit the continuous read mode, Instruction 01011000 must
be written to the communications register while the RDY pin
is low. While in the continuous read mode, the ADC monitors
activity on the DIN line so that it can receive the instruction to
exit the continuous read mode. Additionally, a reset occurs if
40 consecutive 1s are seen on DIN. Therefore, DIN should be
held low in continuous read mode until an instruction is to be
written to the device.
When several channels are enabled, the ADC continuously
steps through the enabled channels and performs one conversion
on each channel each time that it is selected. DOUT/RDY pulses
low when a conversion is available. When the user applies sufficient
SCLK pulses, the data is automatically placed on the DOUT/RDY
pin. If the DAT_STA bit in the mode register is set to 1, the
contents of the status register are output along with the conversion.
The status register indicates the channel to which the conversion
corresponds.
DIN
SCLK
DOUT/RDY
CS
0x5C
DATA
08367-
063
Figure 27. Continuous Read
相關PDF資料
PDF描述
VI-27T-MX-S CONVERTER MOD DC/DC 6.5V 75W
MS27497E10A99SA CONN RCPT 7POS WALL MNT W/SCKT
AD7193BCPZ-RL IC ADC 24BIT SPI 4.8KHZ 32LFCSP
AD7898AR-3REEL7 IC ADC 12BIT SRL HS 5V 8-SOIC
VI-2TW-MX-S CONVERTER MOD DC/DC 5.5V 75W
相關代理商/技術參數
參數描述
AD7193BRUZ 功能描述:IC ADC 24BIT SPI 4.8K 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率(每秒):1M 數據接口:串行,SPI? 轉換器數目:1 功率耗散(最大):- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤(4x4) 包裝:Digi-Reel® 輸入數目和類型:8 個單端,單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7193BRUZ 制造商:Analog Devices 功能描述:IC ADC 24BIT 4.8KHZ TSSOP-28
AD7193BRUZ-REEL 功能描述:IC ADC 24BIT SPI 4.8KHZ 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
AD7194 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, 4.8 kHz, Ultralow Noise, 24-Bit Sigma-Delta ADC with PGA
AD7194BCPZ 功能描述:IC ADC 24BIT SPI 4.8K 32-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極