參數資料
| 型號： | AD7244JR |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 3/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 14BIT LC2MOS DUAL 28SOIC |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 1 |
| 設置時間： | 4µs |
| 位數： | 14 |
| 數據接口： | 串行 |
| 轉換器數目： | 2 |
| 電壓電源： | 雙 ± |
| 功率耗散（最大）： | 195mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC W |
| 包裝： | 管件 |
| 輸出數目和類型： | 2 電壓，雙極 |
| 采樣率（每秒）： | 250k |
AD7242/AD7244
REV. A
–11–
APPLYING THE AD7242/AD7244
Good printed circuit board layout is as important as the overall
circuit design itself in achieving high speed converter perfor-
mance. The AD7242 works on an LSB size of 1.465 mV, while
the AD7244 works on an LSB size of 366
V. Therefore, the
designer must be conscious of minimizing noise in both the
converter itself and in the surrounding circuitry. Switching
mode power supplies are not recommended as the switching
spikes can feed through to the on-chip amplifier. Other causes
of concern are ground loops and digital feedthrough from
microprocessors. These are factors that influence any high
performance converter, and a proper PCB layout that minimizes
these effects is essential for best performance.
LAYOUT HINTS
Ensure that the layout for the printed circuit board has separated
digital and analog lines as much as possible. Take care not to
run any digital track alongside an analog signal track. Establish a
single point analog ground (star ground) separate from the logic
system ground. Place this star ground as close as possible to the
AD7242/AD7244. Connect all analog grounds to this star
ground and also connect the AD7242/AD7244 DGND pins to
this ground. Do not connect any other digital grounds to this
analog ground point.
Low impedance analog and digital power supply common
returns are essential to low noise operation of high performance
converters. Therefore, the foil width for these tracks should be
kept as wide as possible. The use of ground planes minimizes
impedance paths and also guards the analog circuitry from
digital noise.
NOISE
Keep the signal leads on the VOUTA and VOUTB signals and the
signal return leads to AGND as short as possible to minimize
noise coupling. In applications where this is not possible, use a
shielded cable between the DAC outputs and their destination.
Reduce the ground circuit impedance as much as possible since
any potential difference in grounds between the DAC and its
destination device appears as an error voltage in series with the
DAC output.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2704CGW-16#PBF | IC DAC 16BIT QUAD VOUT 44-SSOP |
| LTC2704IGW-14#PBF | IC DAC 14BIT QUAD VOUT 44-SSOP |
| AD669BNZ | IC DAC 16BIT MONO W/VREF 28-DIP |
| AD7237AQ | IC DAC 12BIT W/AMP W/BUFF 24CDIP |
| VI-26T-IV | CONVERTER MOD DC/DC 6.5V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7244JR-REEL | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| AD7244JRZ | 功能描述:IC DAC 14BIT LC2MOS DUAL 28SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD7244JRZ | 制造商:Analog Devices 功能描述:D/A Converter (D-A) IC |
| AD7244JRZ-REEL | 功能描述:IC DAC 14BIT LC2MOS DUAL 28SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| AD7244SQ/883B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:14-Bit Digital-to-Analog Converter |
發(fā)布緊急采購，3分鐘左右您將得到回復。