- 您現在的位置：買賣IC網 > PDF目錄373896 > AD7274BRM (ANALOG DEVICES INC) 3MSPS,10-/12-Bit ADCs in 8-Lead TSOT PDF資料下載
參數資料
| 型號： | AD7274BRM |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 3MSPS,10-/12-Bit ADCs in 8-Lead TSOT |
| 中文描述： | 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| 封裝： | MO-187AA, MSOP-8 |
| 文件頁數： | 10/20頁 |
| 文件大?。?/td> | 243K |
| 代理商： | AD7274BRM |
–
10
–
REV. PrB
PRELIMINARY TECHNICAL DATA
AD7273/AD7274
Preliminary Technical Data
TERMINOLOGY
Integral Nonlinearity (INL)
This is the maximum deviation from a straight line pass-
ing through the endpoints of the ADC transfer function.
For the AD7273/AD7274, the endpoints of the transfer
function are zero scale, a 1/2 LSB below the first code
transition, and full scale, a point 1/2 LSB above the last
code transition.
Differential Nonlinearity (DNL)
This is the difference between the measured and the
ideal 1 LSB change between any two adjacent codes in
the ADC.
Offset Error
This is the deviation of the first code transition (00 . . .
000) to (00 . . . 001) from the ideal, i.e,
AGND + 0.5 LSB
.
Gain Error
This is the deviation of the last code transition (111 . . .
110) to (111 . . . 111) from the ideal, i.e, V
REF
–
1.5LSB after the offset error has been adjusted out.
Total Unadjusted Error (TUE)
This is a comprehensive specification which includes gain,
linearity and offset errors.
Track/Hold Acquisition Time
The Track/Hold acquisition time is the time required
for the output of the track/hold amplifier to reach its
final value, within ±0.5 LSB, after the end of
conversion. See Serial Interface section for more details.
Signal to Noise Ratio (SNR)
This is the measured ratio of signal to noise at the
output to the A/D converter. The signal is the rms value
of the sine wave input. Noise is the rms quantization
error within the Nyquist bandwitdh (fs/2). The rms
value of a sine wave is one half its peak to peak value
divided by
√
2 and the rms value for the quantization
noise is q/
√
12. The ratio is dependant on the number of
quantization levels in the digitization process; the more
levels, the smaller the quantization noise. For an ideal
N-bit converter, the SNR is defined as:
SNR = 6.02 N + 1.76 dB
Thus for a 12-bit converter this is 74 dB, for a 10-bit
converter it is 62 dB.
Practically, though, various error sources in the ADC
cause the measured SNR to be less than the theoretical
value. These errors occur due to integral and differential
nonlinearities, internal AC noise sources, etc.
Signal-to- (Noise + Distortion) Ratio (SINAD)
This is the measured ratio of signal to (noise +
distortion) at the output of the A/D converter. The
signal is the rms value of the sine wave and noise is the
rms sum of all nonfundamentals signals up to half the
sampling frequency (fs/2), including harmonics but
excluding dc.
THD (dB)
=
20 log
V
2
2
+
V
3
2
+
V
4
2
+
V
5
2
+
V
6
2
V
1
Total Harmonic Distortion (THD)
Total harmonic distortion is the ratio of the rms sum of
harmonics to the fundamental. It is defined as:
where
V
1
is the rms amplitude of the fundamental and
V
2
,
V
3
,
V
4
,
V
5
and
V
6
are the rms amplitudes of the second
through the sixth harmonics.
Peak Harmonic or Spurious Noise (SFDR)
Peak harmonic or spurious noise is defined as the ratio of
the rms value of the next largest component in the ADC
output spectrum (up to f
S
/2 and excluding dc) to the rms
value of the fundamental. Normally, the value of this
specification is determined by the largest harmonic in the
spectrum, but for ADCs where the harmonics are buried
in the noise floor, it will be a noise peak.
Intermodulation Distortion (IMD)
With inputs consisting of sine waves at two frequencies, fa
and fb, any active device with nonlinearities will create
distortion products at sum and difference frequencies of
mfa ± nfb where m, n = 0, 1, 2, 3, etc. Intermodulation
distortion terms are those for which neither m nor n are
equal to zero. For example, the second order terms in-
clude (fa + fb) and (fa
–
fb), while the third order terms
include (2fa + fb), (2fa
–
fb), (fa + 2fb) and (fa
–
2fb).
The AD7273/AD7274 are tested using the CCIF standard
where two input frequencies are used (see fa and fb in the
specification page). In this case, the second order terms
are usually distanced in frequency from the original sine
waves while the third order terms are usually at a fre-
quency close to the input frequencies. As a result, the
second and third order terms are specified separately. The
calculation of the intermodulation distortion is as per the
THD specification where it is the ratio of the rms sum of
the individual distortion products to the rms amplitude of
the sum of the fundamentals expressed in dBs.
Power Supply Rejection Ratio (PSRR)
The power supply rejection ratio is defined as the ratio of the
power in the ADC output at full-scale frequency, f, to the
power of a 200 mV p-p sine wave applied to the ADC V
DD
supply of frequency f
s
.
PSRR (dB) = 10
log
(
Pf/ Pf
s
)
Pf
is the power at frequency f in the ADC output;
Pf
s
is
the power at frequency f
s
coupled onto the ADC V
DD
supply.
Aperture Delay
This is the measured interval between the leading edge of the
sampling clock and the point at which the ADC actually takes
the sample.
Aperture Jitter
This is the sample-to-sample variation in the effective point
in time at which the sample is taken.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7274BUJ-REEL | 3MSPS,10-/12-Bit ADCs in 8-Lead TSOT |
| AD7276 | 3MSPS,12-/10-/8-Bit ADCs in 6-Lead TSOT |
| AD7276BRM | 3MSPS,12-/10-/8-Bit ADCs in 6-Lead TSOT |
| AD7276BUJ-REEL | 3MSPS,12-/10-/8-Bit ADCs in 6-Lead TSOT |
| AD7277 | 3MSPS,12-/10-/8-Bit ADCs in 6-Lead TSOT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7274BRM-U2 | 制造商:Analog Devices 功能描述:ADC SGL SAR 3MSPS 12-BIT SERL 8MSOP - Bulk |
| AD7274BRMZ | 功能描述:IC ADC 12BIT 3MSPS HS LP 8MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7274BRMZ2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 MSPS,10-/12-Bit ADCs in 8-Lead TSOT |
| AD7274BRMZ-REEL | 功能描述:IC ADC 12BIT 3MSPS HS LP 8MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7274BRMZ-REEL2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 MSPS,10-/12-Bit ADCs in 8-Lead TSOT |
發布緊急采購，3分鐘左右您將得到回復。