- 您現在的位置：買賣IC網 > PDF目錄373901 > AD7477AAKSZ-REEL73 (Analog Devices, Inc.) 2.35 V to 5.25 V, 1 MSPS, 12-/10-/8-Bit ADCs in 6-Lead SC70 PDF資料下載
參數資料
| 型號： | AD7477AAKSZ-REEL73 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 2.35 V to 5.25 V, 1 MSPS, 12-/10-/8-Bit ADCs in 6-Lead SC70 |
| 中文描述： | 2.35 V至5.25 V，1 MSPS的，12/10/8位ADC的6引腳SC70封裝 |
| 文件頁數： | 17/24頁 |
| 文件大?。?/td> | 580K |
| 代理商： | AD7477AAKSZ-REEL73 |
REV. C
AD7476A/AD7477A/AD7478A
–17–
SCLK frequency one dummy cycle is sufficient to power up the
device and acquire V
IN
, it does not necessarily mean that a full
dummy cycle of 16 SCLKs must always elapse to power up the
device and acquire V
IN
fully; 1
μ
s will be sufficient to power up
the device and acquire the input signal. If, for example, a
5 MHz SCLK frequency was applied to the ADC, the cycle
time would be 3.2
μ
s. In one dummy cycle, 3.2
μ
s, the part
would be powered up and V
IN
acquired fully. However, after 1
μ
s
with a 5 MHz SCLK, only five SCLK cycles would have elapsed.
At this stage, the ADC would be fully powered up and the sig-
nal acquired. In this case, the
CS
can be brought high after the
10th SCLK falling edge and brought low again after a time,
t
QUIET
, to initiate the conversion.
When power supplies are first applied to the AD7476A/AD7477A/
AD7478A, the ADC may power up in either the power-down or
normal mode. Because of this, it is best to allow a dummy cycle
to elapse to ensure that the part is fully powered up before attempt-
ing a valid conversion. Likewise, if it is intended to keep the part
in the power-down mode while not in use and the user wishes
the part to power up in power-down mode, the dummy cycle
may be used to ensure that the device is in power-down by
executing a cycle such as that shown in Figure 10. Once supplies
are applied to the AD7476A/AD7477A/AD7478A, the power-up
time is the same as that when powering up from the power-
down mode. It takes approximately 1
μ
s to power up fully if the
part powers up in normal mode. It is not necessary to wait 1
μ
s
before executing a dummy cycle to ensure the desired mode of
operation. Instead, the dummy cycle can occur directly after
power is supplied to the ADC. If the first valid conversion is
performed directly after the dummy conversion, care must be
taken to ensure that an adequate acquisition time has been
allowed. As mentioned earlier, when powering up from the
power-down mode, the part will return to track upon the first
SCLK edge applied after the falling edge of
CS
. However,
when the ADC powers up initially after supplies are applied,
the track-and-hold will already be in track. This means, assum-
ing one has the facility to monitor the ADC supply
current, if
the ADC powers up in the desired mode of operation and thus
a dummy cycle is not required to change the mode, a dummy
cycle is not required to place the track-and-hold into track.
POWER VS. THROUGHPUT RATE
By using the power-down mode on the AD7476A/AD7477A/
AD7478A when not converting, the average power consumption
of the ADC decreases at lower throughput rates. Figure 12 shows
how as the throughput rate is reduced, the device remains in its
power-down state longer and the average power consumption over
time drops accordingly.
For example, if the AD7476A/AD7477A/AD7478A are oper-
ated in a continuous sampling mode with a throughput rate of
100 kSPS and an SCLK of 20 MHz (V
DD
= 5 V) and the devices
are placed in the power-down mode between conversions, the
power consumption is calculated as follows. The power dissipation
during normal operation is 17.5 mW (V
DD
= 5 V). If the power-up
time is one dummy cycle, i.e., 1
μ
s, and the remaining conversion
VALID DATA
SDATA
SCLK
CS
1
10
12
14
16
AD7476A/AD7477A/AD7478A
Figure 9. Normal Mode Operation
THREE-STATE
SDATA
SCLK
CS
1
10
12
14
16
2
Figure 10. Entering Power-Down Mode
INVALID DATA
SDATA
SCLK
CS
1
10
12
14
16
A
1
16
VALID DATA
THE PART IS FULLY
POWERED UP WITH
V
IN
FULLY ACQUIRED
THE PART
BEGINS TO
POWER UP
Figure 11. Exiting Power-Down Mode
相關PDF資料 |
PDF描述 |
|---|---|
| AD7478AAKSZ-500RL73 | 2.35 V to 5.25 V, 1 MSPS, 12-/10-/8-Bit ADCs in 6-Lead SC70 |
| AD7477AAKSZ-REEL | Circular Connector; MIL SPEC:MIL-C-5015; Body Material:Metal; Series:GT; No. of Contacts:12; Connector Shell Size:28; Connecting Termination:Solder; Circular Shell Style:Square Flange Receptacle; Body Style:Straight |
| AD7478AAKSZ-REEL | Circular Connector; MIL SPEC:MIL-C-5015; Body Material:Metal; Series:GT; No. of Contacts:3; Connector Shell Size:28; Connecting Termination:Solder; Circular Shell Style:Square Flange Receptacle; Body Style:Straight |
| AD7477AAKSZ-REEL7 | GT 12C 6#12 6#16 PIN RECP WALL |
| AD7478AAKSZ-REEL7 | GT 12C 6#12 6#16 SKT RECP WALL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7477AARM | 制造商:Rochester Electronics LLC 功能描述:10-BIT LOW POWER ADC IN USOIC PKG I.C - Bulk 制造商:Analog Devices 功能描述:IC 10BIT ADC SMD 7477 MSOP8 |
| AD7477AARM-REEL | 制造商:Analog Devices 功能描述:ADC SGL SAR 1MSPS 10-BIT SERL 8MSOP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:10-BIT LOW POWER ADC IN USOIC PKG I.C - Tape and Reel |
| AD7477AARM-REEL7 | 制造商:Rochester Electronics LLC 功能描述:10-BIT LOW POWER ADC IN USOIC PKG I.C - Tape and Reel 制造商:Analog Devices 功能描述: |
| AD7477AARMZ | 功能描述:IC ADC 10BIT 1MSPS 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7477AARMZ-REEL | 功能描述:IC ADC 10BIT 1MSPS 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發布緊急采購，3分鐘左右您將得到回復。