參數資料
型號: AD7477AAKSZ-REEL
廠商: Analog Devices Inc
文件頁數: 13/29頁
文件大小: 0K
描述: IC ADC 10BIT 1MSPS LP SC70-6
標準包裝: 10,000
位數: 10
采樣率(每秒): 1M
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 17.5mW
電壓電源: 單電源
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 6-TSSOP,SC-88,SOT-363
供應商設備封裝: SC-70-6
包裝: 帶卷 (TR)
輸入數目和類型: 1 個單端,單極
配用: EVAL-AD7477CBZ-ND - BOARD EVALUATION FOR AD7477
AD7476A/AD7477A/AD7478A
Rev. F | Page 19 of 28
SDATA
SCLK
CS
1
10
12
14
16
AD7476A/AD7477A/AD7478A
02930-020
VALID DATA
Figure 20. Normal Mode Operation
THREE-STATE
SDATA
SCLK
CS
1
10
12
14
16
2
02930-021
Figure 21. Entering Power-Down Mode
INVALID DATA
SDATA
SCLK
CS
1
10
12
14
16
A
1
16
VALID DATA
THE PART IS FULLY
POWERED UP WITH
VIN FULLY ACQUIRED
THE PART
BEGINS TO
POWER UP
02930-022
Figure 22. Exiting Power-Down Mode
When power supplies are first applied to the AD7476A/AD7477A/
AD7478A, the ADC can power up in either the power-down or
normal modes. Because of this, it is best to allow a dummy cycle
to elapse to ensure that the part is fully powered up before
attempting a valid conversion. Likewise, if it is intended to keep
the part in the power-down mode while not in use and the user
wishes the part to power up in power-down mode, the dummy
cycle can be used to ensure that the device is in power-down by
executing a cycle such as that shown in Figure 22. Once supplies
are applied to the AD7476A/AD7477A/AD7478A, the power-up
time is the same as that when powering up from the power-down
mode. It takes approximately 1 μs to power up fully if the part
powers up in normal mode. It is not necessary to wait 1 μs before
executing a dummy cycle to ensure the desired mode of operation.
Instead, a dummy cycle can occur directly after power is
supplied to the ADC. If the first valid conversion is performed
directly after the dummy conversion, care must be taken to
ensure that an adequate acquisition time has been allowed. As
mentioned earlier, when powering up from the power-down
mode, the part returns to track upon the first SCLK edge
applied after the falling edge of CS. However, when the ADC
initially powers up after supplies are applied, the track-and-hold
is already in track. This means, assuming one has the facility to
monitor the ADC supply current, if the ADC powers up in the
desired mode of operation and thus a dummy cycle is not
required to change the mode, a dummy cycle is not required to
place the track-and-hold into track.
相關PDF資料
PDF描述
MS3106E22-33P CONN PLUG 7POS STRAIGHT W/PINS
VE-21T-MX-S CONVERTER MOD DC/DC 6.5V 75W
MS27473E10B13S CONN PLUG 13POS STRAIGHT W/SCKT
AD7477ARTZ-REEL7 IC ADC 10BIT 1MSPS SOT23-6
VI-21T-MX-S CONVERTER MOD DC/DC 6.5V 75W
相關代理商/技術參數
參數描述
AD7477AAKSZ-REEL3 制造商:AD 制造商全稱:Analog Devices 功能描述:2.35 V to 5.25 V, 1 MSPS, 12-/10-/8-Bit ADCs in 6-Lead SC70
AD7477AAKSZ-REEL7 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 10-bit Serial 6-Pin SC-70 T/R
AD7477AAKSZ-REEL73 制造商:AD 制造商全稱:Analog Devices 功能描述:2.35 V to 5.25 V, 1 MSPS, 12-/10-/8-Bit ADCs in 6-Lead SC70
AD7477AARM 制造商:Rochester Electronics LLC 功能描述:10-BIT LOW POWER ADC IN USOIC PKG I.C - Bulk 制造商:Analog Devices 功能描述:IC 10BIT ADC SMD 7477 MSOP8
AD7477AARM-REEL 制造商:Analog Devices 功能描述:ADC SGL SAR 1MSPS 10-BIT SERL 8MSOP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:10-BIT LOW POWER ADC IN USOIC PKG I.C - Tape and Reel