- 您現在的位置：買賣IC網 > PDF目錄373910 > AD7610BCPZ1 (Analog Devices, Inc.) 16-Bit, 250 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC PDF資料下載
參數資料
| 型號： | AD7610BCPZ1 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 16-Bit, 250 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| 中文描述： | 16位，250 kSPS的，單極/雙極可編程輸入PulSAR系列ADC的 |
| 文件頁數： | 23/32頁 |
| 文件大?。?/td> | 591K |
| 代理商： | AD7610BCPZ1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7610
INTERFACES
DIGITAL INTERFACE
The AD7610 has a versatile digital interface that can be set up
as either a serial or a parallel interface with the host system. The
serial interface is multiplexed on the parallel data bus. The AD7610
digital interface also accommodates 2.5 V, 3.3 V, or 5 V logic. In
most applications, the OVDD supply pin is connected to the host
system interface 2.5 V to 5.25 V digital supply. Finally, by using
the OB/2C input pin, both twos complement or straight binary
coding can be used.
Two signals, CS and RD, control the interface. When at least
one of these signals is high, the interface outputs are in high
impedance. Usually, CS allows the selection of each AD7610
in multicircuit applications and is held low in a single AD7610
design. RD is generally used to enable the conversion result on
the data bus.
RESET
The RESET input is used to reset the AD7610. A rising edge on
RESET aborts the current conversion (if any) and tristates the
data bus. The falling edge of RESET resets the AD7610 and clears
the data bus and configuration register. See Figure 34 for the
RESET timing details.
Rev. 0 | Page 23 of 32
RESET
DATA
BUS
BUSY
CNVST
t
8
t
9
0
Figure 34. RESET Timing
PARALLEL INTERFACE
The AD7610 is configured to use the parallel interface when
SER/PAR is held low.
Master Parallel Interface
Data can be continuously read by tying CS and RD low, thus
requiring minimal microprocessor connections. However, in
this mode, the data bus is always driven and cannot be used in
shared bus applications (unless the device is held in RESET).
Figure 35 details the timing for this mode.
t
1
BUSY
DBUS
PREVIOUS CONVERSION DATA
NEW DATA
CNVST
CS = RD = 0
t
10
t
4
t
11
t
3
0
Figure 35. Master Parallel Data Timing for Reading (Continuous Read)
Slave Parallel Interface
In slave parallel reading mode, the data can be read either after
each conversion, which is during the next acquisition phase, or
during the following conversion, as shown in Figure 36 and
Figure 37, respectively. When the data is read during the conver-
sion, it is recommended that it is read only during the first half
of the conversion phase. This avoids any potential feedthrough
between voltage transients on the digital interface and the most
critical analog conversion circuitry.
CURRENT
CONVERSION
t
13
t
12
BUSY
DATA
BUS
RD
CS
0
Figure 36. Slave Parallel Data Timing for Reading (Read After Convert)
PREVIOUS
CONVERSION
t
13
t
12
t
3
BUSY
DATA
BUS
CNVST,
RD
CS = 0
t
4
t
1
0
Figure 37. Slave Parallel Data Timing for Reading (Read During Convert)
相關PDF資料 |
PDF描述 |
|---|---|
| AD7610BCPZ-RL | 16-Bit, 250 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| AD7610BSTZ | 16-Bit, 250 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| AD7610BSTZ-RL | 16-Bit, 250 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| AD7621 | 16-Bit, 1 LSB INL, 3 MSPS PulSAR ADC |
| AD7621ACP | 16-Bit, 1 LSB INL, 3 MSPS PulSAR ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7610BCPZ-RL | 功能描述:IC ADC 16BIT 250KSPS 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7610BSTZ | 功能描述:IC ADC 16BIT 250KSPS 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7610BSTZ-RL | 功能描述:IC ADC 16BIT 250KSPS 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7611ACP | 制造商:Analog Devices 功能描述:1MSPS, 16-BIT ADC S/W PROG. INPUT RANGES - Bulk |
| AD7611AST | 制造商:Analog Devices 功能描述:1MSPS, 16-BIT ADC S/W PROG. INPUT RANGES - Bulk |
發布緊急采購，3分鐘左右您將得到回復。