- 您現在的位置：買賣IC網 > PDF目錄8997 > AD7628KNZ (Analog Devices Inc)IC DAC 8BIT DUAL MULTIPLY 20-DIP PDF資料下載
參數資料
| 型號： | AD7628KNZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 8BIT DUAL MULTIPLY 20-DIP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 18 |
| 設置時間： | 400ns |
| 位數： | 8 |
| 轉換器數目： | 2 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 450mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 20-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 20-PDIP |
| 包裝： | 管件 |
| 輸出數目和類型： | 2 電流，單極；2 電流，雙極 |
| 采樣率（每秒）： | 2.9M |
| 產品目錄頁面： | 785 (CN2011-ZH PDF) |
AD7628
–6–
REV. A
APPLICATIONS INFORMATION
Application Hints
To ensure system performance consistent with AD7628 specifi-
cations, careful attention must be given to the following points:
1. GENERAL GROUND MANAGEMENT: AC or transient
voltages between the AD7628 AGND and DGND can cause
noise injection into the analog output. The simplest method
of ensuring that voltages at AGND and DGND are equal is
to tie AGND and DGND together at the AD7628. In more
omplex systems where the AGND–DGND intertie is on the
backplane, it is recommended that diodes be connected in
inverse parallel between the AD7628 AGND and DGND
pins (1N914 or equivalent).
2. OUTPUT AMPLIFIER OFFSET: CMOS DACs exhibit a
code-dependent output resistance which, in turn, causes a
code-dependent amplifier noise gain. The effect is a code-
dependent differential nonlinearity term at the amplifier
output that depends on VOS (VOS is amplifier input offset
voltage). This differential nonlinearity term adds to the R/2R
differential nonlinearity. To maintain monotonic operation, it
is recommended that amplifier VOS be no greater than 10% of
1 LSB over the temperature range of interest.
3. HIGH FREQUENCY CONSIDERATIONS: The output
capacitance of a CMOS DAC works in conjunction with the
amplifier feedback resistance to add a pole to the open loop
response. This can cause ringing or oscillation. Stability can
be restored by adding a phase compensation capacitor in
parallel with the feedback resistor.
DYNAMIC PERFORMANCE
The dynamic performance of the two DACs in the AD7628 will
depend on the gain and phase characteristics of the output am-
plifiers, together with the optimum choice of the PC board lay-
out and decoupling components. Figure 6 shows the relationship
between input frequency and channel-to-channel isolation.
Figure 6. Channel-to-Channel Isolation
Figure 7. Suggested PC Board Layout for AD7628 with
AD644 Dual Op Amp
Figure 7 shows a printed circuit layout for the AD7628 and the
AD644 dual op amp, which minimizes feedthrough and crosstalk.
SINGLE SUPPLY APPLICATIONS
The AD7628 DAC R-2R ladder termination resistors are con-
nected to AGND within the device. This arrangement is par-
ticularly convenient for single supply operation because AGND
may be biased at any voltage between DGND and VDD. Figure
8 shows a circuit that provides two +5 V to +8 V analog outputs
by biasing AGND +5 V up from DGND. The two DAC refer-
ence inputs are tied together and a reference input voltage is ob-
tained without a buffer amplifier by making use of the constant
and matched impedances of the DAC A and DAC B reference
inputs. Current flows through the two DAC R-2R ladders into
R1, and R1 is adjusted until the VREF A and VREF B inputs are
at +2 V. The two analog output voltages range from +5 V to
+8 V for DAC codes 00000000 to l l l l l l l l .
Figure 8. AD7628 Single Supply Operation
Figure 9 shows DAC A of the AD7628 connected in a positive
reference, voltage switching mode. This configuration is useful
because VOUT is the same polarity as VIN, allowing single supply
operation. However, to retain specified linearity, VIN must be in
the range 0 V to +2.5 V and the output buffered or loaded with
a high impedance (see Figure 10). Note that the input voltage is
connected to the DAC OUT A, and the output voltage is taken
from the DAC VREF A pin.
Figure 9. AD7628 Single Supply, Voltage Switching Mode
Figure 10. Typical AD7628 Performance in Single Supply
Voltage Switching Mode
相關PDF資料 |
PDF描述 |
|---|---|
| ICS84330CM-01LFT | IC FREQ SYNTHESIZER 28SOIC |
| VI-JTL-MZ-F3 | CONVERTER MOD DC/DC 28V 25W |
| AD7628KPZ | IC DAC 8BIT DUAL MULTIPLY 20PLCC |
| AD7303BNZ | IC DAC 8BIT DUAL R-R 8-DIP |
| VI-2NK-MW-F2 | CONVERTER MOD DC/DC 40V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7628KNZ | 制造商:Analog Devices 功能描述:CMOS DUAL 8 BIT D/A CONVE 制造商:Analog Devices 功能描述:IC, DAC, 8BIT, 2.9MSPS, DIP-20 |
| AD7628KP | 功能描述:IC DAC 8BIT DUAL W/BUFF 20-PLCC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| AD7628KP/+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Digital-to-Analog Converter |
| AD7628KP-REEL | 功能描述:IC DAC 8BIT DUAL W/BUFF 20-PLCC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD7628KPZ | 功能描述:IC DAC 8BIT DUAL MULTIPLY 20PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。