- 您現在的位置：買賣IC網 > PDF目錄373911 > AD7651AST (ANALOG DEVICES INC) 16-Bit 100 kSPS PulSAR Unipolar ADC with Reference PDF資料下載
參數資料
| 型號： | AD7651AST |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 16-Bit 100 kSPS PulSAR Unipolar ADC with Reference |
| 中文描述： | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, PQFP48 |
| 封裝： | MS-026BBC, LQFP-48 |
| 文件頁數： | 17/28頁 |
| 文件大?。?/td> | 709K |
| 代理商： | AD7651AST |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7651
TYPICAL CONNECTION DIAGRAM
Figure 22 shows a typical connection diagram for the AD7651.
Analog Input
Figure 23
shows an equivalent circuit of the input structure of
the AD7651.
Driver Amplifier Choice
Although the AD7651 is easy to drive, the driver amplifier needs
to meet the following requirements:
The driver amplifier and the AD7651 analog input circuit
must be able to settle for a full-scale step of the capacitor
array at a 16-bit level (0.0015%). In the amplifier’s data
sheet, settling at 0.1% to 0.01% is more commonly speci-
fied. This could differ significantly from the settling time at
a 16-bit level and should be verified prior to driver
selection. The tiny op amp OP184, which combines ultra
low noise and high gain-bandwidth, meets this settling
time requirement.
Figure 23. Equivalent Analog Input Circuit
The two diodes, D1 and D2, provide ESD protection for the
analog inputs IN and INGND. Care must be taken to ensure
that the analog input signal never exceeds the supply rails by
more than 0.3 V. This will cause these diodes to become
forward-biased and start conducting current. These diodes can
handle a forward-biased current of 100 mA maximum. For
instance, these conditions could eventually occur when the
input buffer’s (U1) supplies are different from AVDD. In such a
case, an input buffer with a short-circuit current limitation can
be used to protect the part.
The noise generated by the driver amplifier needs to be
kept as low as possible in order to preserve the SNR and
transition noise performance of the AD7651. The noise
coming from the driver is filtered by the AD7651 analog
input circuit 1-pole low-pass filter made by R1 and C2 or
by the external filter, if one is used.
C2
R1
D1
D2
C1
IN
OR INGND
AGND
AVDD
02965-0-008
The driver needs to have a THD performance suitable to
that of the AD7651.
The
OP184
,
OP162
or
AD8519
meet these requirements and are
usually appropriate for almost all applications. As an alternative,
in very high speed and noise-sensitive applications, the
AD8021
with an external 10 pF compensation capacitor can be used.
This capacitor should have good linearity as an NPO ceramic or
mica type. Moreover, the use of a noninverting +1 gain
arrangement is recommended and helps to obtain the best
signal-to-noise ratio.
This analog input structure allows the sampling of the
differential signal between IN and INGND. Unlike other
converters, INGND is sampled at the same time as IN. By using
this differential input, small signals common to both inputs are
rejected. For instance, by using INGND to sense a remote signal
ground, ground potential differences between the sensor and
the local ADC ground are eliminated.
The
AD8022
could also be used if a dual version is needed and
gain of 1 is present. The
AD829
is an alternative in applications
where high frequency (above 100 kHz) performance is not
required. In gain of 1 applications, it requires an 82 pF
compensation capacitor. The
AD8610
is an option when low
bias current is needed in low frequency applications.
During the acquisition phase, the impedance of the analog input
IN can be modeled as a parallel combination of capacitor C1
and the network formed by the series connection of R1 and C2.
C1 is primarily the pin capacitance. R1 is typically 3250 and is
a lumped component made up of some serial resistors and the
on resistance of the switches. C2 is typically 60 pF and is mainly
the ADC sampling capacitor. During the conversion phase,
where the switches are opened, the input impedance is limited
to C1. R1 and C2 make a 1-pole low-pass filter that reduces
undesirable aliasing effect and limits the noise.
When the source impedance of the driving circuit is low, the
AD7651 can be driven directly. Large source impedances will
significantly affect the ac performance, especially total
harmonic distortion.
Rev. 0 | Page 17 of 28
相關PDF資料 |
PDF描述 |
|---|---|
| AD7651ASTRL | 16-Bit 100 kSPS PulSAR Unipolar ADC with Reference |
| AD7654 | Dual 2-Channel Simultaneous Sampling SAR 500 kSPS 16-Bit ADC |
| AD7654ACP | Dual 2-Channel Simultaneous Sampling SAR 500 kSPS 16-Bit ADC |
| AD7654ACPRL | Dual 2-Channel Simultaneous Sampling SAR 500 kSPS 16-Bit ADC |
| AD7654AST | Dual 2-Channel Simultaneous Sampling SAR 500 kSPS 16-Bit ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7651ASTRL | 制造商:Analog Devices 功能描述: |
| AD7651ASTZ | 功能描述:IC ADC 16BIT 100KSPS 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7651ASTZ | 制造商:Analog Devices 功能描述:16BIT SAR ADC REF 7651 LQFP48 |
| AD7651ASTZRL | 功能描述:IC ADC 16BIT UNIPOLAR 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7652 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit 1 MSPS SAR Unipolar ADC with Ref |
發布緊急采購，3分鐘左右您將得到回復。