參數資料
型號: AD7671
廠商: Analog Devices, Inc.
英文描述: 16-Bit 1 MSPS SAR Unipolar ADC with Ref
中文描述: 16位1 MSPS的特區單極型ADC檔
文件頁數: 22/23頁
文件大?。?/td> 336K
代理商: AD7671
REV. PrA
PRELIMINARY TECHNICAL DATA
–22–
AD7667
at right angles to each other. T his will reduce the effect of
feedthrough through the board.
T he power supplies lines to the AD7667 should use as
large trace as possible to provide low impedance paths and
reduce the effect of glitches on the power supplies lines.
Good decoupling is also important to lower the supplies
impedance presented to the AD7667 and reduce the magni-
tude of the supply spikes. Decoupling ceramic capacitors,
typically 100 nF, should be placed on each power supplies
pins AVDD, DVDD, and OVDD close to, and ideally right
up against, these pins and their corresponding ground pins.
Additionally, low ESR 10 μF capacitors should be located in
the vicinity of the ADC to further reduce low frequency
ripple.
T he DVDD supply of the AD7667 can be either a separate
supply or come from the analog supply AVDD or the digi-
tal interface supply OVDD. When the system digital supply
is noisy, or fast switching digital signals are present, it is
recommended that if no separate supply available, connect
the DVDD digital supply to the analog supply, AVDD,
through an RC filter as shown in Figure 5, and connect
the system supply to the interface digital supply, OVDD,
and the remaining digital circuitry. When DVDD is powered
from the system supply, it is useful to insert a bead to fur-
ther reduce high-frequency spikes.
T he AD7667 has five different ground pins: INGND, REF-
GND, AGND, DGND, and OGND. INGND is used to
sense the analog input signal. REFGND senses the refer-
ence voltage and should be a low impedance return to the
reference because it carries pulsed currents. AGND is the
ground to which most internal ADC analog signals are
referenced. T his ground must be connected with the least
resistance to the analog ground plane. DGND must be
tied to the analog or digital ground plane depending on the
configuration. OGND is connected to the digital system
ground.
E valuating the AD 7667 Performance
A recommended layout for the AD7667 is outlined in the
evaluation board for the AD7667. T he evaluation board
package includes a fully assembled and tested evaluation
board, documentation, and software for controlling the board
from a PC via the Eval-Control Board.
相關PDF資料
PDF描述
AD7651ACP 16-Bit 100 kSPS PulSAR Unipolar ADC with Reference
AD7651AST 16-Bit 100 kSPS PulSAR Unipolar ADC with Reference
AD7651ASTRL 16-Bit 100 kSPS PulSAR Unipolar ADC with Reference
AD7654 Dual 2-Channel Simultaneous Sampling SAR 500 kSPS 16-Bit ADC
AD7654ACP Dual 2-Channel Simultaneous Sampling SAR 500 kSPS 16-Bit ADC
相關代理商/技術參數
參數描述
AD7671ACP 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 16-bit Parallel/Serial 48-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:16-BIT, 1MSPS CMOS ADC - Bulk 制造商:Analog Devices 功能描述:Analog Devices AD7671ACP Analog to Digital Converters (ADC)
AD7671ACPRL 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 16-bit Parallel/Serial 48-Pin LFCSP EP T/R
AD7671ACPZ 功能描述:IC ADC 16BIT CMOS 1MSPS 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率(每秒):20M 數據接口:并聯 轉換器數目:2 功率耗散(最大):155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP(7x7) 包裝:Digi-Reel® 輸入數目和類型:4 個單端,單極;2 個差分,單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7671ACPZRL 功能描述:IC ADC 16BIT CMOS 1MSPS 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極
AD7671AST 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 16-bit Parallel/Serial 48-Pin LQFP 制造商:Analog Devices 功能描述:IC 16-BIT ADC