- 您現在的位置：買賣IC網 > PDF目錄10124 > AD7710AR-REEL7 (Analog Devices Inc)IC ADC 24BIT DIFF INP 24-SOIC PDF資料下載
參數資料
| 型號： | AD7710AR-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT DIFF INP 24-SOIC |
| 標準包裝： | 400 |
| 位數： | 24 |
| 采樣率（每秒）： | 1.03k |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 45mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個差分，單極；2 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7710
REV. G
–17–
USING THE AD7710
SYSTEM DESIGN CONSIDERATIONS
The AD7710 operates differently from successive approxima-
tion ADCs or integrating ADCs. Because it samples the signal
continuously, like a tracking ADC, there is no need for a start
convert command. The output register is updated at a rate
determined by the first notch of the filter, and the output can be
read at any time, either synchronously or asynchronously.
Clocking
The AD7710 requires a master clock input, which may be an
external TTL/CMOS compatible clock signal applied to the
MCLK IN pin with the MCLK OUT pin left unconnected.
Alternatively, a crystal of the correct frequency can be connected
between MCLK IN and MCLK OUT, in which case the clock
circuit will function as a crystal-controlled oscillator. For lower
clock frequencies, a ceramic resonator may be used instead of
the crystal. For these lower frequency oscillators, external
capacitors may be required on either the ceramic resonator or
on the crystal.
The input sampling frequency, the modulator sampling fre-
quency, the –3 dB frequency, the output update rate, and the
calibration time are all directly related to the master clock fre-
quency fCLK IN. Reducing the master clock frequency by a factor
of 2 will halve the above frequencies and update rate and will
double the calibration time.
The current drawn from the DVDD power supply is also directly
related to fCLK IN. Reducing fCLK IN by a factor of 2 will halve the
DVDD current but will not affect the current drawn from the
AVDD power supply.
System Synchronization
If multiple AD7710s are operated from a common master clock,
they can be synchronized to update their output registers simul-
taneously. A falling edge on the
SYNC input resets the filter and
places the AD7710 into a consistent, known state. A common
signal to the AD7710s’
SYNC inputs will synchronize their
operation. This would typically be done after each AD7710 has
performed its own calibration or has had calibration coefficients
loaded to it.
The
SYNC input can also be used to reset the digital filter in
systems where the turn-on time of the digital power supply
(DVDD) is very long. In such cases, the AD7710 will start oper-
ating internally before the DVDD line has reached its minimum
operating level, 4.75 V. With a low DVDD voltage, the
AD7710’s internal digital filter logic does not operate correctly.
Thus, the AD7710 may have clocked itself into an incorrect
operating condition by the time that DVDD has reached its cor-
rect level. The digital filter will be reset upon issue of a calibra-
tion command (whether it is self-calibration, system calibration,
or background calibration) to the AD7710. This ensures correct
operation of the AD7710. In systems where the power-on
default conditions of the AD7710 are acceptable, and no cali-
bration is performed after power-on, issuing a
SYNC pulse to
the AD7710 will reset the AD7710’s digital filter logic. An R, C
on the
SYNC line, with R, C time constant longer than the
DVDD power-on time, will perform the SYNC function.
Accuracy
Sigma-delta ADCs, like VFCs and other integrating ADCs, do
not contain any source of nonmonotonicity and inherently offer
no missing codes performance. The AD7710 achieves excellent
linearity by the use of high quality, on-chip silicon dioxide
capacitors, which have a very low capacitance/voltage coefficient.
The device also achieves low input drift through the use of chopper
stabilized techniques in its input stage. To ensure excellent perfor-
mance over time and temperature, the AD7710 uses digital
calibration techniques that minimize offset and gain error.
Autocalibration
Autocalibration on the AD7710 removes offset and gain errors
from the device. A calibration routine should be initiated on the
device whenever there is a change in the ambient operating
temperature or supply voltage. It should also be initiated if there
is a change in the selected gain, filter notch, or bipolar/unipolar
input range. However, if the AD7710 is in its background cali-
bration mode, these changes are all automatically taken care of
(after the settling time of the filter has been allowed for).
The AD7710 offers self-calibration, system calibration, and
background calibration facilities. For calibration to occur on the
selected channel, the on-chip microcontroller must record the
modulator output for two different input conditions. These are
zero-scale and full-scale points. With these readings, the micro-
controller can calculate the gain slope for the input to output
transfer function of the converter. Internally, the part works
with a resolution of 33 bits to determine its conversion result of
either 16 bits or 24 bits.
The AD7710 also provides the facility to write to the on-chip
calibration registers, and, in this manner, the span and offset for
the part can be adjusted by the user. The offset calibration regis-
ter contains a value that is subtracted from all conversion
results, while the full-scale calibration register contains a value
that is multiplied by all conversion results. The offset calibration
coefficient is subtracted from the result prior to the multiplica-
tion by the full-scale coefficient. In the first three modes out-
lined here, the
DRDY line indicates that calibration is complete
by going low. If
DRDY is low before (or goes low during) the
calibration command, it may take up to one modulator cycle
before
DRDY goes high to indicate that calibration is in
progress. Therefore,
DRDY should be ignored for up to one
modulator cycle after the last bit of the calibration command is
written to the control register.
Self-Calibration
In the self-calibration mode with a unipolar input range, the
zero-scale point used in determining the calibration coefficients
is with both inputs shorted (that is, AIN(+) = AIN(–) = VBIAS)
and the full-scale point is VREF. The zero-scale coefficient is
determined by converting an internal shorted inputs node. The
full-scale coefficient is determined from the span between this
shorted inputs conversion and a conversion on an internal VREF
node. The self-calibration mode is invoked by writing the appro-
priate values (0, 0, 1) to the MD2, MD1, and MD0 bits of the
control register. In this calibration mode, the shorted inputs
node is switched in to the modulator first and a conversion is
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2NK-MX-F3 | CONVERTER MOD DC/DC 40V 75W |
| LTC1419CG | IC A/D CONV 14BIT SAMPLNG 28SSOP |
| IDT7202LA15TPI | IC FIFO ASYNCH 1KX9 15NS 28DIP |
| MS27468T15F5SB | CONN RCPT 5POS JAM NUT W/SCKT |
| IDT7202LA12TPG | IC FIFO ASYNCH 1KX9 12NS 28DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7710ARZ | 功能描述:IC ADC 24BIT DIFF INP 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7710ARZ | 制造商:Analog Devices 功能描述:IC ADC 24BIT 1.02KSPS SOIC-24 |
| AD7710ARZ-REEL | 功能描述:IC ADC 24BIT DIFF INP 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7710ARZ-REEL7 | 功能描述:IC ADC 24BIT DIFF INP 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7710SQ | 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 1.028KSPS 24BIT SERL 24CDIP - Rail/Tube 制造商:Analog Devices 功能描述:IC ADC 24BIT DIFF INP 24-CDIP 制造商:Analog Devices 功能描述:IC ADC 24BIT SERIAL DIP-24 制造商:Analog Devices 功能描述:IC, ADC, 24BIT, SERIAL, DIP-24 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC 24 BIT SIGMA DELTA ADC IC 制造商:Analog Devices 功能描述:IC, ADC, 24BIT, SERIAL, DIP-24; Resolution (Bits):24bit; Supply Voltage Type:Single; Supply Voltage Min:5V; Supply Voltage Max:10V; Supply Current:4mA; Digital IC Case Style:DIP; No. of Pins:24; Input Channel Type:Differential 制造商:Analog Devices 功能描述:CONVERTER - ADC 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 1.028ksps 24-bit Serial 24-Pin CDIP |
發布緊急采購，3分鐘左右您將得到回復。