- 您現在的位置：買賣IC網 > PDF目錄10129 > AD7710AR-REEL (Analog Devices Inc)IC ADC 24BIT DIFF INP 24-SOIC PDF資料下載
參數資料
| 型號： | AD7710AR-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 17/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT DIFF INP 24-SOIC |
| 標準包裝： | 1,000 |
| 位數： | 24 |
| 采樣率（每秒）： | 1.03k |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 45mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個差分，單極；2 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
REV. G
–24–
AD7710
SIMPLIFYING THE EXTERNAL CLOCKING MODE
INTERFACE
In many applications, the user may not need to write to the on-chip
calibration registers. In this case, the serial interface to the AD7710
in external clocking mode can be simplified by connecting the
TFS
line to the A0 input of the AD7710 (see Figure 14). This means
that any write to the device will load data to the control register
(because A0 is low while
TFS is low), and any read to the de-
vice will access data from the output data register or from the
calibration registers (because A0 is high while
RFS is low). Note
that in this arrangement the user does not have the capability of
reading from the control register.
AD7710
SDATA
SCLK
TFS
A0
FOUR
INTERFACE
LINES
RFS
Figure 14. Simplified Interface with
TFS Connected to A0
Another method of simplifying the interface is to generate the
TFS signal from an inverted RFS signal. However, generating
the signals the opposite way around (
RFS from an inverted
TFS) will cause writing errors.
MICROCOMPUTER/MICROPROCESSOR INTERFACING
The AD7710’s flexible serial interface allows for easy interface
to most microcomputers and microprocessors. Figure 15 shows
a flowchart for a typical programming sequence for reading data
from the AD7710 to a microcomputer, while Figure 16 shows a
flowchart for writing data to the AD7710. Figures 17, 18, and
19 show some typical interface circuits.
Figure 15 shows continuous read operations from the AD7710
output register, where the
DRDY line is continuously polled.
Depending on the microprocessor configuration, the
DRDY line
may come to an interrupt input, in which case the
DRDY will
automatically generate an interrupt without being polled. Read-
ing the serial buffer could be anything from one read operation
up to three read operations (where 24 bits of data are read into
an 8-bit serial register). A read operation to the control/calibra-
tion registers is similar, but, in this case, the status of
DRDY
can be ignored. The A0 line is brought low when the
RFS line
is brought low during a read register.
The flowchart also shows the bits being reversed after they have
been read in from the serial port. This depends on whether the
microprocessor expects the MSB of the word first or the LSB of
the word first. The AD7710 outputs the MSB first.
Figure 16 shows a single 24-bit write operation to the AD7710
control or calibration registers. This shows data being trans-
ferred from data memory to the accumulator before being writ-
ten to the serial buffer. Some microprocessor systems allow data
to be written directly to the serial buffer from data memory.
Writing data to the serial buffer from the accumulator generally
consists of either two or three write operations, depending on
the size of the serial buffer.
NO
YES
BRING
RFS LOW
3
REVERSE
ORDER OF BITS
BRING
RFS HIGH
POLL DRDY
CONFIGURE AND
INITIALIZE
C/ P
SERIAL PORT
DRDY
LOW?
BRING
RFS, TFS HIGH
START
READ
SERIAL BUFFER
Figure 15. Flowchart for Continuous Read Operations
to the AD7710
Figure 16 also shows the option of the bits being reversed before
being written to the serial buffer. This depends on whether the
first bit transmitted by the microprocessor is the MSB or the
LSB. The AD7710 expects the MSB as the first bit in the data
stream. In cases where the data is being read or being written in
bytes and the data has to be reversed, the bits have to be reversed
for every byte.
相關PDF資料 |
PDF描述 |
|---|---|
| IDT7201LA12PDG | IC MEM FIFO 512X9 12NS 28-PDIP |
| VI-23X-IW-F1 | CONVERTER MOD DC/DC 5.2V 100W |
| SP312AET-L | IC DVR/RCVR RS232 5V SGL 18WSOIC |
| AD1674KRZ-REEL | IC ADC 12BIT 100KSPS 28-SOIC |
| MS3476L14-4S | CONN PLUG 4POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7710AR-REEL7 | 功能描述:IC ADC 24BIT DIFF INP 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7710ARZ | 功能描述:IC ADC 24BIT DIFF INP 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7710ARZ | 制造商:Analog Devices 功能描述:IC ADC 24BIT 1.02KSPS SOIC-24 |
| AD7710ARZ-REEL | 功能描述:IC ADC 24BIT DIFF INP 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7710ARZ-REEL7 | 功能描述:IC ADC 24BIT DIFF INP 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發布緊急采購，3分鐘左右您將得到回復。