- 您現在的位置：買賣IC網 > PDF目錄378276 > AD7739BRU-REEL (ANALOG DEVICES INC) 8-Channel, High Throughput, 24-Bit Sigma-Delta ADC PDF資料下載
參數資料
| 型號： | AD7739BRU-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 8-Channel, High Throughput, 24-Bit Sigma-Delta ADC |
| 中文描述： | 8-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO24 |
| 封裝： | MS-153AD, TSSOP-24 |
| 文件頁數： | 30/32頁 |
| 文件大?。?/td> | 380K |
| 代理商： | AD7739BRU-REEL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁
AD7739
CALIBRATION
The AD7739 provides zero-scale self-calibration, and zero- and
full-scale system calibration capability that can effectively
reduce the offset error and gain error to the order of the noise.
After each conversion, the ADC conversion result is scaled
using the ADC calibration registers and the relevant channel
calibration registers before being written to the data register.
Rev. 0 | Page 30 of 32
For unipolar ranges:
Data = ((ADC result – R × ADC ZS Cal. reg.)
× ADC FS reg./(0x20 0000) – R × Ch. ZS Cal. reg.)
× Ch. FS Cal. reg./(0x20 0000)
For bipolar ranges:
Data = ((ADC result – R × ADC ZS Cal. reg.)
× ADC FS reg./(0x40 0000) + (0x80 0000) – R × Ch. ZS Cal. reg.)
× Ch. FS Cal. reg./(0x20 0000)
where the ADC result is in the range of 0 to 0xFF FFFF.
R = 1 for input ranges +1.25 V, ±1.25 V, +2.5 V, and ±2.5 V
R = 2 for input ranges +0.625 V, and ±0.625 V
Note that the channel zero-scale calibration register has the
format of a sign bit and a 22-bit channel offset value.
To start any calibration, write the relevant mode bits to the
AD7739 mode register. After the calibration is complete, the
contents of the corresponding calibration registers are updated,
all RDY bits in the ADC status register are set, the SYNC pin
goes low, and the AD7739 reverts to idle mode. The calibration
duration is the same as the conversion time configured on the
selected channel. A longer conversion time gives less noise and
yields a more exact calibration; therefore, use at least the default
conversion time to initiate any calibration.
ADC Zero-Scale Self-Calibration
The ADC zero-scale self-calibration can reduce the ADC offset
error in the chopping disabled mode. If repeated after a
temperature change, it can also reduce the offset drift error in
the chopping disabled mode.
The zero-scale self-calibration is performed on internally
shorted ADC inputs. The negative analog input terminal on the
selected channel is used to set the ADC zero-scale calibration
common mode. Therefore, either the negative terminal of the
selected differential pair or the AINCOM on the single-ended
channel configuration should be driven to a proper common-
mode voltage.
It is recommended that the ADC zero-scale calibration register
be updated only as part of an ADC zero-scale self-calibration.
ADC Full-Scale Self-Calibration
The ADC full-scale self-calibration can reduce the ADC full-
scale error for the +2.5 V and ±2.5 V input range. If repeated
after a temperature change, it can also reduce the full-scale drift.
The ADC full-scale self-calibration is performed with a +2.5 V
input voltage range on internally generated full-scale voltage
(V
REF
), regardless of the input voltage range set in the channel
setup register. Full-scale errors in the ±1.25 V, +1.25 V, ±0.625 V,
and +0.625 V ranges are not calibrated as this would require an
accurate low voltage source other than the reference.
If the 1.25 V or 0.625 V ranges are used on any channel, the
ADC full-scale self-calibration is not recommended. A system
full-scale calibration should be performed if accurate gains
need to be achieved on these ranges.
It is recommended that the ADC full-scale calibration register
be updated only as part of an ADC full-scale self-calibration for
the +2.5 V and ±2.5 V input range.
Per Channel System Calibration
The per channel system calibration can reduce the system offset
error and the system gain error. If repeated after a temperature
change, it can also reduce the system offset and gain drifts.
If the per channel system calibrations are used, these should be
initiated in the following order: a channel zero-scale system
calibration, followed by a channel full-scale system calibration.
The system calibration is affected by the ADC zero-scale and
full-scale calibration registers. Therefore, if both self-calibration
and system calibration are used in the system, an ADC self-
calibration should be performed first, followed by a system
calibration cycle.
The voltage range in the channel setup register should be set
before executing the channel system calibration.
While executing a system calibration, the fully settled system
zero-scale voltage signal or system full-scale voltage signal must
be connected to the selected channel analog inputs.
The per channel calibration registers can be read, stored, or
modified and written back to the AD7739. Note that when
writing the calibration registers, the AD7739 must be in idle
mode. Note that outside the specified calibration range,
calibration is possible, but the performance may degrade
(see the System Calibration section in Table 1).
相關PDF資料 |
PDF描述 |
|---|---|
| AD7739BRU-REEL7 | 8-Channel, High Throughput, 24-Bit Sigma-Delta ADC |
| AD79024 | LC2MOS 20-Bit Data Acquisition System |
| AD8152 | 34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch |
| AD8152-EVAL | 34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch |
| AD8152JBP | 34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7739BRU-REEL7 | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 3.05Msps 24-bit Serial 24-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 15.133KSPS 24BIT SERL 24TSSOP - Tape and Reel |
| AD7739BRUZ | 功能描述:IC ADC 24BIT 8-CH 24-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7739BRUZ | 制造商:Analog Devices 功能描述:IC, ADC, 24BIT, 15.1KSPS, TSSOP-24 |
| AD7739BRUZ-REEL7 | 功能描述:IC ADC 24BIT 8CH SIG-DEL 24TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD773A | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 20 MSPS Monolithic A/D Converter |
發布緊急采購，3分鐘左右您將得到回復。