- 您現在的位置：買賣IC網 > PDF目錄10184 > AD7776AR (Analog Devices Inc)IC ADC 10BIT 1CH HS 24-SOIC PDF資料下載
參數資料
| 型號： | AD7776AR |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 12/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 1CH HS 24-SOIC |
| 標準包裝： | 31 |
| 位數： | 10 |
| 采樣率（每秒）： | 37.8k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個單端，單極 |
AD7776/AD7777/AD7778
–9–
REV. A
Table I. AD7776/AD7777/AD7778 Truth Table for Microprocessor Interfacing
CS
RD
WR
DB0–DB9
Function/Comments
1X
*
X
*
High Z
Data Port High Impedance
01
j
CR Data
Load control register (CR) data to control register and start a conversion.
0
k
1
ADC Data
ADC data placed on data bus. Depending upon location CR6 of the control register, one or two
Read instructions are required.
If CR6 is low, i.e., single-channel conversion selected, a read instruction returns the contents of
ADCREG1. Succeeding read instructions continue to return the contents of ADCREG1.
If CR6 is high, i.e., simultaneous sampling (double conversion) selected, the first read instruction
returns the contents of ADCREG1 while the second read instruction returns the contents of
ADCREG2. A third read instruction returns ADCREG1 again, the fourth ADCREG2, etc.
*X = Don’t Care
DESIGN INFORMATION
Layout Hints
Ensure that the layout for the printed circuit board has the digi-
tal and analog grounds separated as much as possible. Take care
not to run any digital track alongside an analog signal track.
Guard (screen) the analog input(s) with RTN.
Establish a single-point analog ground separate from the logic
system ground and as close as possible to the AD7776/AD7777/
AD7778. Both the RTN and AGND pins on the AD7776/
AD7777/AD7778 and all other signal grounds should be con-
nected to this single point analog ground. In turn, this star
ground should be connected to the digital ground at one point
only—preferably at the low impedance power supply itself.
Low impedance analog and digital power supply common returns
are important for correct operation of the devices, so make the
foil width for these tracks as wide as possible.
To ensure a low impedance +5 V power supply at the actual VCC
pin, it is necessary to use bypass capacitors from the pin itself to
DGND. A 4.7
F tantalum capacitor in parallel with a 0.1 F
ceramic capacitor is sufficient.
ADC Corruption
Executing a read instruction to the AD7776/AD7777/AD7778
while a conversion is in progress immediately halts the conversion
and returns invalid data over the data bus. The
BUSY/ INT
output pin should be monitored closely and all read instructions
to the AD7776/AD7777/AD7778 prevented while this output
shows that a conversion is in progress.
Executing a write instruction to the AD7776/AD7777/AD7778
while a conversion is in progress immediately halts the conversion,
while the falling edge of
WR driving the BUSY/INT output high.
The analog input(s) is sampled as normal, and a new conversion
sequence (dependent upon CR6) is started.
ADC Conversion Time
Although each conversion takes only 14 CLKIN cycles, it can take
between 4.5 and 5.5 CLKIN cycles to acquire the analog input(s)
after the
WR input goes high and before any conversions start.
TERMINOLOGY
Relative Accuracy
For the AD7776/AD7777/AD7778, relative accuracy or endpoint
nonlinearity is the maximum deviation, in LSBs, of the ADC’s
actual code transition points from a straight line drawn between
the endpoints of the ADC transfer function.
Differential Nonlinearity
Differential nonlinearity is the difference between the measured
change and the ideal 1 LSB change between any two adjacent
codes. A specified maximum differential nonlinearity of
±1 LSB
ensures no missed codes.
Bias Offset Error
For an ideal 10-bit ADC, the output code for an input voltage
equal to VBIAS should be midscale. The bias offset error is the
difference between the actual midpoint voltage for midscale code
and VBIAS, expressed in LSBs.
Bias Offset Error Match
This is a measure of how closely the bias offset errors of all
channels track each other. The bias offset error match of any
channel must be no further away than 10 LSBs from the bias
offset error of any other channel, regardless of whether the
channels are independently sampled or simultaneously sampled.
Plus and Minus Full-Scale Error
The input channels of the ADC can be considered to have
bipolar (positive and negative) input ranges, but are referred to
VBIAS (or REFIN) instead of AGND. Positive full-scale error for
the ADC is the difference between the actual input voltage
required to produce the plus full-scale code transition and the ideal
input voltage (VBIAS + VSWING –1.5 LSB), expressed in LSBs.
Minus full-scale error is similarly specified for the minus full-scale
code transition, relative to the ideal input voltage for this
transition (VBIAS – VSWING + 0.5 LSB). Note that the full-scale
errors for the ADC input channels are measured after their
respective bias offset errors have been adjusted out.
Plus and Minus Full-Scale Error Match
This is a measure of how closely the full-scale errors of all
channels track each other. The full-scale error match of any channel
must be no further away than 10 LSBs from the respective
full-scale error of any other channel, regardless of whether the
channels are independently sampled or simultaneously sampled.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3120F12-10SW | CONN RCPT 10POS WALL MNT W/SCKT |
| VI-B63-IV-S | CONVERTER MOD DC/DC 24V 150W |
| VE-27K-MY | CONVERTER MOD DC/DC 40V 50W |
| VE-B3L-MW-F3 | CONVERTER MOD DC/DC 28V 100W |
| AD7854ARZ | IC ADC 12BIT PARALLEL LP 28SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7776AR-REEL | 功能描述:IC ADC 10BIT 1CH HS 24-SOIC T/R RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7776ARZ | 功能描述:IC ADC 10BIT 1CHAN HS 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD7776ARZ-REEL | 功能描述:IC ADC 10BIT 1CHAN HS 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7777 | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS, High Speed 1-, 4- & 8-Channel 10-Bit ADCs |
| AD7777AN | 制造商:Analog Devices 功能描述:ADC Single SAR 378ksps 10-bit Parallel 28-Pin PDIP 制造商:Analog Devices 功能描述:4 CH 10-BIT ADC IC - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:4 CH 10-BIT ADC IC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。