- 您現在的位置：買賣IC網 > PDF目錄10315 > AD7792BRUZ-REEL (Analog Devices Inc)IC ADC 16BIT 3CH LP 16-TSSOP PDF資料下載
參數資料
| 型號： | AD7792BRUZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/33頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT 3CH LP 16-TSSOP |
| 標準包裝： | 2,500 |
| 位數： | 16 |
| 采樣率（每秒）： | 500 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 2.5mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 3 個差分，單極；3 個差分，雙極 |
| 配用： | EVAL-AD7792EBZ-ND - BOARD EVALUATION FOR AD7792 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
AD7792/AD7793
Rev. B | Page 14 of 32
ON-CHIP REGISTERS
The ADC is controlled and configured via a number of on-chip
registers, which are described on the following pages. In the
following descriptions, set implies a Logic 1 state and cleared
implies a Logic 0 state, unless otherwise stated.
COMMUNICATIONS REGISTER
RS2, RS1, RS0 = 0, 0, 0
The communications register is an 8-bit write-only register. All
communications to the part must start with a write operation to
the communications register. The data written to the
communications register determines whether the next
operation is a read or write operation, and to which register this
operation takes place. For read or write operations, once the
subsequent read or write operation to the selected register is
complete, the interface returns to where it expects a write
operation to the communications register. This is the default
state of the interface and, on power-up or after a reset, the ADC
is in this default state waiting for a write operation to the
communications register. In situations where the interface
sequence is lost, a write operation of at least 32 serial clock
cycles with DIN high returns the ADC to this default state by
resetting the entire part. Table 11 outlines the bit designations
for the communications register. CR0 through CR7 indicate the
bit location, CR denoting the bits are in the communications
register. CR7 denotes the first bit of the data stream. The
number in parentheses indicates the power-on/reset default
status of that bit.
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
WEN(0)
R/W(0)
RS2(0)
RS1(0)
RS0(0)
CREAD(0)
0(0)
Table 11. Communications Register Bit Designations
Bit Location
Bit Name
Description
CR7
WEN
Write Enable Bit. A 0 must be written to this bit so that the write to the communications register actually
occurs. If a 1 is the first bit written, the part does not clock on to subsequent bits in the register. It stays at this
bit location until a 0 is written to this bit. Once a 0 is written to the WEN bit, the next seven bits are loaded to
the communications register.
CR6
R/W
A 0 in this bit location indicates that the next operation is a write to a specified register. A 1 in this position
indicates that the next operation is a read from the designated register.
CR5 to CR3
RS2 to
RS0
Register Address Bits. These address bits are used to select which of the ADC’s registers are being selected
during this serial interface communication. See Table 12.
CR2
CREAD
Continuous Read of the Data Register. When this bit is set to 1 (and the data register is selected), the serial
interface is configured so that the data register can be continuously read. For example, the contents of the
data register are placed on the DOUT pin automatically when the SCLK pulses are applied after the RDY pin
goes low to indicate that a conversion is complete. The communications register does not have to be written
to for data reads. To enable continuous read mode, the instruction 01011100 must be written to the
communications register. To exit the continuous read mode, the instruction 01011000 must be written to the
communications register while the RDY pin is low. While in continuous read mode, the ADC monitors activity
on the DIN line so that it can receive the instruction to exit continuous read mode. Additionally, a reset occurs
if 32 consecutive 1s are seen on DIN. Therefore, DIN should be held low in continuous read mode until an
instruction is to be written to the device.
CR1 to CR0
0
These bits must be programmed to Logic 0 for correct operation.
Table 12. Register Selection
RS2
RS1
RS0
Register
Register Size
0
Communications Register During a Write Operation
8-bit
0
Status Register During a Read Operation
8-bit
0
1
Mode Register
16-bit
0
1
0
Configuration Register
16-bit
0
1
Data Register
16-/24-bit
1
0
ID Register
8-bit
1
0
1
IO Register
8-bit
1
0
Offset Register
16-bit (AD7792)/24-bit (AD7793)
1
Full-Scale Register
16-bit (AD7792)/24-bit (AD7793)
相關PDF資料 |
PDF描述 |
|---|---|
| AD7708BRUZ-REEL | IC ADC 16BIT R-R 8/10CH 28TSSOP |
| C091 31W005 100 2 | CONN MALE RCPT 5POS FRONT MT |
| MS3111F10-98S | CONN RCPT 6POS CBL MNT W/SCKT |
| D38999/26WJ61AB | CONN HSG PLUG 61POS STRGHT PINS |
| VE-22W-MY | CONVERTER MOD DC/DC 5.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7792BRUZ-REEL1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3-Channel, Low Noise, Low Power, 16-/24-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
| AD7793 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, 16/24-Bit Sigma-Delta ADC with Low-Noise In-Amp and Embedded Reference |
| AD7793B | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, 16/24-Bit Sigma-Delta ADC with Low-Noise In-Amp and Embedded Reference |
| AD7793BRU | 功能描述:IC ADC 24BIT 3CH LP 16-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7793BRU-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 470sps 24-bit Serial 16-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.47KSPS 24BIT SERL 16TSSOP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。