- 您現在的位置：買賣IC網 > PDF目錄373917 > AD7818ARM (Analog Devices, Inc.) Single- and 4-Channel, 9 us, 10-Bit ADCs with On-Chip Temperature Sensor PDF資料下載
參數資料
| 型號： | AD7818ARM |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Single- and 4-Channel, 9 us, 10-Bit ADCs with On-Chip Temperature Sensor |
| 中文描述： | 與單核和4通道，9我們，10位ADC片上溫度傳感器 |
| 文件頁數： | 16/20頁 |
| 文件大?。?/td> | 279K |
| 代理商： | AD7818ARM |
REV. C
–16–
AD7816/AD7817/AD7818
Read Operation
Figure 20 shows the timing diagram for a serial read from the
AD7817.
CS
is brought low to enable the serial interface and RD/
WR
is set logic high to indicate that the data transfer is a serial read
from the AD7817. The rising edge of RD/
WR
clocks out the first
data bit (DB9), subsequent bits are clocked out on the falling edge
of SCLK (except for the first falling SCLK edge) and are valid on
the rising edge. 10 bits of data are transferred during a read opera-
tion. However, the user has the choice of clocking only eight bits if
the full 10 bits of the conversion result are not required. The serial
data can be accessed in a number of bytes if 10 bits of data are
being read. However, RD/
WR
must remain high for the duration of
the data transfer operation. Before starting a new data read opera-
tion the RD/
WR
signal must be brought low and high again. At the
end of the read operation, the D
OUT
line enters a high impedance
state on the rising edge of the
CS
or the falling edge of RD/
WR
,
whichever occurs first. The readback process is a destructive
process in that once the data is read back it is erased. A conversion
must be done again; otherwise no data will be read back.
Write Operation
Figure 20 also shows a control byte write operation to the AD7817.
The RD/
WR
input goes low to indicate to the part that a serial
write is about to occur. The AD7817 control byte is loaded on
the rising edge of the first eight clock cycles of the serial clock
with data on all subsequent clock cycles being ignored. To carry
out a second successive write operation, the RD/
WR
signal must
be brought high and low again.
Simplifying the Serial Interface
To minimize the number of interconnect lines to the AD7817,
the user can connect the
CS
line to DGND. This is possible if
the AD7817 is not sharing the serial bus with another device. It
is also possible to tie the D
IN
and D
OUT
lines together. This
arrangement is compatible with the 8051 microcontroller. The
68HC11, 68HC05, and PIC16Cxx can be configured to operate
with a single serial data line. In this way the number of lines
required to operate the serial interface can be reduced to three,
i.e., RD/
WR
, SCLK, and D
IN/OUT
(see Figure 6).
AD7816 AND AD7818 SERIAL INTERFACE MODE
The serial interface on the AD7816 and AD7818 is a 3-wire
interface with read and write capabilities. Data is read from the
DB9
DB8
DB7
DB0
DB1
DB7
DB6
DB5
DB1
DB0
SCLK
D
IN
1
3
2
1
2
3
9
10
RD/
WR
CS
t
4
t
7
t
10
t
14a
t
14b
t
13
t
12
t
11
t
8
t
9
t
5
t
6
8
7
CONTROL BYTE
D
OUT
Figure 20. AD7817 Serial Interface Timing Diagram
output register and the control byte is written to the AD7816
and AD7818 via the D
IN/OUT
line. The part operates in a slave
mode and requires an externally applied serial clock to the SCLK
input to access data from the data register or write the control
byte. The RD/
WR
line is used to determine whether data is
being written to or read from the AD7816 and AD7818. When
data is being written to the devices the RD/
WR
line is set logic
low and when data is being read from the part the line is set
logic high (see Figure 21). The serial interface on the AD7816
and AD7818 are designed to allow the part to be interfaced to
systems that provide a serial clock that is synchronized to the
serial data, such as the 80C51, 87C51, 68HC11, 68HC05, and
PIC16Cxx microcontrollers.
Read Operation
Figure 21 shows the timing diagram for a serial read from the
AD7816 and AD7818. The RD/
WR
is set logic high to indicate
that the data transfer is a serial read from the devices. When
RD/
WR
is logic high the D
IN/OUT
pin becomes a logic output
and the first data bit (DB9) appears on the pin. Subsequent bits
are clocked out on the falling edge of SCLK, starting with the
second SCLK falling edge after RD/
WR
goes high and are valid
on the rising edge of SCLK. Ten bits of data are transferred
during a read operation. However the user has the choice of
clocking only eight bits if the full 10 bits of the conversion result
are not required. The serial data can be accessed in a number of
bytes if 10 bits of data are being read; however, RD/
WR
must
remain high for the duration of the data transfer operation. To
carry out a successive read operation the RD/
WR
pin must be
brought logic low and high again. At the end of the read opera-
tion, the D
IN/OUT
pin becomes a logic input on the falling edge
of RD/
WR
.
Write Operation
A control byte write operation to the AD7816 and AD7818 is
also shown in Figure 21. The RD/
WR
input goes low to indicate
to the part that a serial write is about to occur. The AD7816
and AD7818 control bytes are loaded on the rising edge of the
first eight clock cycles of the serial clock with data on all subse-
quent clock cycles being ignored. To carry out a successive write
to the AD7816 or AD7818 the RD/
WR
pin must be brought
logic high and low again.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7816AR-REEL7 | Single- and 4-Channel, 9 us, 10-Bit ADCs with On-Chip Temperature Sensor |
| AD7818AR-REEL7 | Single- and 4-Channel, 9 us, 10-Bit ADCs with On-Chip Temperature Sensor |
| AD7819YN | +2.7 V to +5.5 V, 200 kSPS 8-Bit Sampling ADC |
| AD7819YR | +2.7 V to +5.5 V, 200 kSPS 8-Bit Sampling ADC |
| AD7819YRU | Circular Connector; Body Material:Aluminum Alloy; Series:KPSE06; No. of Contacts:15; Connector Shell Size:14; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Circular Contact Gender:Socket; Insert Arrangement:14-15 RoHS Compliant: No |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7818ARM-REEL | 功能描述:IC ADC 10BIT W/TEMP SNSR 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
| AD7818ARM-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 10-bit Serial 8-Pin MSOP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 100KSPS 10-BIT SERL 8MSOP - Tape and Reel |
| AD7818ARMZ | 功能描述:IC ADC 10BIT W/TEMP SENSOR 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:3,000 系列:- 功能:溫度開關 傳感器類型:內部 感應溫度:85°C 分界點 精確度:±6°C（最小值） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:開路漏極 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:ADT6501SRJZP085RL7-ND |
| AD7818ARMZ-REEL | 功能描述:IC ADC 10BIT W/TEMP SENSOR 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
| AD7818ARMZ-REEL7 | 功能描述:IC ADC 10BIT W/TEMP SENSOR 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
發布緊急采購，3分鐘左右您將得到回復。