- 您現在的位置：買賣IC網 > PDF目錄10186 > AD7864ASZ-2REEL (Analog Devices Inc)IC ADC 12BIT PAR 520K 4CH 44MQFP PDF資料下載
參數資料
| 型號： | AD7864ASZ-2REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 28/28頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT PAR 520K 4CH 44MQFP |
| 標準包裝： | 800 |
| 位數： | 12 |
| 采樣率（每秒）： | 520k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 120mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-QFP |
| 供應商設備封裝： | 44-MQFP（10x10） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 4 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁
AD7864
Rev. D | Page 9 of 28
TERMINOLOGY
Channel-to-Channel Isolation
Signal-to-(Noise + Distortion) Ratio
Channel-to-channel isolation is a measure of the level of
crosstalk between channels. It is measured by applying a full-
scale 50 kHz sine wave signal to all nonselected input channels
and determining how much that signal is attenuated in the
selected channel. The figure given is the worst case across all
four channels.
This is the measured ratio of signal-to-(noise + distortion) at
the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the rms sum of all nonfundamental signals
up to half the sampling frequency (fS/2), excluding dc. The ratio
depends on the number of quantization levels in the digitization
process; the more levels, the smaller the quantization noise. The
theoretical signal-to-(noise + distortion) ratio for an ideal N-bit
converter with a sine wave input is given by
Relative Accuracy
Relative accuracy, or endpoint nonlinearity, is the maximum
deviation from a straight line passing through the endpoints of
the ADC transfer function.
Signal-to-(Noise + Distortion) = (6.02 N + 1.76) dB
Thus, for a 12-bit converter, this is 74 dB.
Differential Nonlinearity
Total Harmonic Distortion (THD)
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
THD is the ratio of the rms sum of harmonics to the
fundamental. For the AD7864, it is defined as
Positive Full-Scale Error
1
6
5
4
3
2
V
THD
2
log
20
)
dB
(
+
=
This is the deviation of the last code transition (01...110 to 01...111)
from the ideal, 4 × VREF 3/2 LSB (AD7864-1, ±10 V), or 2 ×
VREF 3/2 LSB (AD7864-1, ±5 V range), or VREF 3/2 LSB
(AD7864-3, ±2.5 V range), after the bipolar offset error has
been adjusted out.
where V1 is the rms amplitude of the fundamental, and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through the
fifth harmonics.
Positive Full-Scale Error (AD7864-2, 0 V to 2.5 V and 0 V to 5 V)
Peak Harmonic or Spurious Noise
This is the deviation of the last code transition (11...110 to 11...111)
from the ideal 2 × VREF 3/2 LSB (AD7864-2, 0 V to 5 V range)
or VREF 3/2 LSB (AD7864-2, 0 V to 2.5 V range), after the
unipolar offset error has been adjusted out.
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is deter-
mined by the largest harmonic in the spectrum, but for parts
where the harmonics are buried in the noise floor, it is a noise peak.
Bipolar Zero Error (AD7864-1, ±10 V/±5 V, AD7864-3, ±2.5 V)
This is the deviation of the midscale transition (all 0s to all 1s)
from the ideal, AGND 1/2 LSB.
Intermodulation Distortion
Unipolar Offset Error (AD7864-2, 0 V to 2.5 V and 0 V to 5 V)
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities creates distortion products
at sum and difference frequencies of mfa ± nfb, where m, n = 0,
1, 2, 3, and so on. Intermodulation terms are those for which
neither m nor n are equal to zero. For example, second-order
terms include (fa + fb) and (fa fb), whereas third-order terms
include (2 fa + fb), (2 fa fb), (fa + 2 fb), and (fa 2 fb).
This is the deviation of the first code transition (00...000 to
00...001) from the ideal, AGND + 1/2 LSB.
Negative Full-Scale Error (AD7864-1, ±10 V/±5 V, and
AD7864-3, ±2.5 V)
This is the deviation of the first code transition (10...000 to
10...001) from the ideal, 4 × VREF + 1/2 LSB (AD7864-1, ±10 V),
2 × VREF + 1/2 LSB (AD7864-1, ±5 V range) or VREF + 1/2 LSB
(AD7864-3, ±2.5 V range), after bipolar zero error has been
adjusted out.
The AD7864 is tested using the CCIF standard, where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second- and third-order terms are of different
significance. The second-order terms are usually distanced in
frequency from the original sine waves, whereas the third-order
terms are usually at a frequency close to the input frequencies. As
a result, the second- and third-order terms are specified separately.
The calculation of the intermodulation distortion is as per the
THD specification where it is the ratio of the rms sum of the
individual distortion products to the rms amplitude of the funda-
mental expressed in decibels.
Track-and-Hold Acquisition Time
Track-and-hold acquisition time is the time required for the
output of the track-and-hold amplifier to reach its final value,
within ±1/2 LSB, after the end of a conversion (the point at
which the track-and-hold returns to track mode). It also applies
to situations where there is a step input change on the input
voltage applied to the selected VINxA/VINxB input of the AD7864.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27484P12A35P | CONN PLUG 22POS STRAIGHT W/PINS |
| SF6382-5PG-520 | CONN PLUG 5POS CABLE PIN |
| SP206ET-L/TR | IC TXRX RS232 SERIAL 24WSOIC |
| VE-25J-IU-F3 | CONVERTER MOD DC/DC 36V 200W |
| VI-2ND-CU-F3 | CONVERTER MOD DC/DC 85V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7864ASZ-2REEL2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, Simultaneous Sampling, High Speed, 12-Bit ADC |
| AD7864ASZ-3 | 功能描述:IC ADC 12BIT PAR 520K 4CH 44MQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7864ASZ-32 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, Simultaneous Sampling, High Speed, 12-Bit ADC |
| AD7864ASZ-3REEL | 功能描述:IC ADC 12BIT PAR 520K 4CH 44MQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7864ASZ-3REEL2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, Simultaneous Sampling, High Speed, 12-Bit ADC |
發布緊急采購，3分鐘左右您將得到回復。