- 您現在的位置：買賣IC網 > PDF目錄10064 > AD7872KRZ-REEL (Analog Devices Inc)IC ADC 14BIT SAMPLING 16SOIC PDF資料下載
參數資料
| 型號： | AD7872KRZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT SAMPLING 16SOIC |
| 標準包裝： | 1,000 |
| 位數： | 14 |
| 采樣率（每秒）： | 83k |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 95mW |
| 電壓電源： | 雙 ± |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC W |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，雙極 |
AD7871/AD7872
–6–
REV. D
CONVERTER DETAILS
The AD7871/AD7872 is a complete 14-bit A/D converter, re-
quiring no external components apart from power supply
decoupling capacitors. It is comprised of a 14-bit successive ap-
proximation ADC based on a fast settling voltage-output DAC,
a high speed comparator and CMOS SAR, a track/hold ampli-
fier, a 3 V buried Zener reference, a clock oscillator and control
logic.
INTERNAL REFERENCE
The AD7871/AD7872 has an on-chip temperature compensated
buried Zener reference that is factory trimmed to 3 V
± 10 mV.
Internally it provides both the DAC reference and the dc bias
required for bipolar operation. Reference noise is minimized by
connecting a capacitor between CREF and AGND. For specified
operation this capacitor should be 10 nF. The reference output
is available (REF OUT) and capable of providing up to 500
A to
an external load.
The maximum recommended capacitance on REF OUT for
normal operation is 50 pF. If the reference is required for use
external to the AD7871/AD7872, it should be decoupled with a
200
resistor in series with a parallel combination of a 10 F
tantalum capacitor and a 0.1
F ceramic capacitor. These
decoupling components are required to remove voltage spikes
caused by the AD7871/AD7872’s internal operation.
Figure 3. Reference Circuit
TRACK-AND-HOLD AMPLIFIER
The track-and-hold amplifier on the analog input of the
AD7871/AD7872 allows the ADC to accurately convert an in-
put sine wave of 6 V peak-peak amplitude to 14-bit accuracy.
The input bandwidth of the track/hold amplifier is much greater
than the Nyquist rate of the ADC even when the ADC is oper-
ated at its maximum throughput rate. The 0.1 dB cutoff fre-
quency occurs typically at 500 kHz. The track/hold amplifier
acquires an input signal to 14-bit accuracy in less than 2
s. The
overall throughput rate is determined by the conversion time
plus the track/hold amplifier acquisition time. For a 2 MHz
input clock the throughput time is 12
s maximum.
Figure 4. Analog Input
The operation of the track/hold amplifier is essentially transpar-
ent to the user. The track/hold amplifier goes from its tracking
mode to its hold mode at the start of conversion. If the
CONVST input is used to start conversion, then the track to
hold transition occurs on the rising edge of
CONVST. If CS on
the AD7871 starts conversion, this transition occurs on the fall-
ing edge of
CS.
ANALOG INPUT
Figure 4 shows the AD7871/AD7872 analog input. The analog
input range is
±3 V into an input resistance of typically 15 k.
The designed code transitions occur midway between successive
integer LSB values (i.e., 1/2 LSB, 3/2 LSBs, 5/2 LSBs . . . FS
–3/2 LSBs). The output code is twos-complement binary with
1 LSB = FS/16384 = 6 V/16384 = 366
V. The ideal input/out-
put transfer function is shown in Figure 5.
Figure 5. Bipolar Input/Output Transfer Function
BIPOLAR OFFSET AND FULL-SCALE ADJUSTMENT
When the AD7871/AD7872’s offset and full-scale errors need to
be adjusted, offset error must be adjusted first. This is achieved
by trimming the offset of the op amp driving the analog input of
the AD7871/AD7872 while the input voltage is 1/2 LSB below
AGND. The trim procedure is as follows: apply a voltage of
–0.183 mV (–1/2 LSB) at V1 in Figure 6 and adjust the op amp
offset voltage until the ADC output code flickers between 11
1111 1111 1111 and 00 0000 0000 0000.
Figure 6. Bipolar Adjust Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MS27473T24A61PC | CONN PLUG 61POS STRAIGHT W/PINS |
| AD7872BRZ-REEL | IC ADC 14BIT SAMPLING 16SOIC |
| MS27467T19B32SB | CONN PLUG 32POS STRAIGHT W/SCKT |
| MS27466T21A35PA | CONN RCPT 79POS WALL MNT W/PINS |
| MS3106F28-9S | CONN PLUG 12POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7872TQ | 制造商:Analog Devices 功能描述:ADC SGL SAR 83KSPS 14BIT SERL 16CDIP - Rail/Tube 制造商:Analog Devices 功能描述:IC ADC 14BIT SAMPLING 16-CDIP 制造商:Analog Devices 功能描述:IC 14-BIT ADC 制造商:Analog Devices 功能描述:CONVERTER - ADC |
| AD7872TQ/883B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 14-Bit |
| AD7872TQ3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete 14-Bit, Sampling ADCs |
| AD7873 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Touch Screen Digitizer |
| AD7873ACP | 制造商:Analog Devices 功能描述:TOUCH SCREEN DIGITIZER |
發(fā)布緊急采購，3分鐘左右您將得到回復。