- 您現在的位置：買賣IC網 > PDF目錄9712 > AD7873BRQZ-REEL7 (Analog Devices Inc)IC ADC 12BIT TOUCHSCREEN 16QSOP PDF資料下載
參數資料
| 型號： | AD7873BRQZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/29頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT TOUCHSCREEN 16QSOP |
| 標準包裝： | 1,000 |
| 類型： | 電阻 |
| 觸摸面板接口： | 4 線 |
| 輸入數/鍵： | 1 TSC |
| 分辨率（位）： | 12 b |
| 評估套件： | 可供 |
| 數據接口： | 串行 |
| 數據速率/采樣率 (SPS，BPS)： | 125k |
| 電壓基準： | 外部，內部 |
| 電源電壓： | 2.2 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
AD7873
Data Sheet
Rev. F | Page 18 of 28
PEN INTERRUPT REQUEST
The pen interrupt equivalent circuitry is outlined in Figure 33.
By connecting a pull-up resistor (10 k to 100 k) between +VCC
and this CMOS logic open-drain output, the PENIRQ output
remains high normally. If PENIRQ is enabled (see Table 8), when
the touch screen connected to the AD7873 is touched by a pen
or finger, the PENIRQ output goes low, initiating an interrupt to
a microprocessor. This can then instruct a control word to be
written to the AD7873 to initiate a conversion. This output can
also be enabled between conversions during power-down (see
Table 8), allowing power-up to be initiated only when the
screen is touched. The result of the first touch screen coordinate
conversion after power-up is valid, assuming any external
reference is settled to the 12-bit or 8-bit level as required.
Figure 34 assumes that the PENIRQ function was enabled in
the last write or that the part was just powered up so PENIRQ is
enabled by default. Once the screen is touched, the PENIRQ
output goes low a time tPEN later. This delay is approximately
5 s, assuming a 10 nF touch screen capacitance, and varies
with the touch screen resistance actually used. Once the START
bit is detected, the pen interrupt function is disabled and
the PENIRQ cannot respond to screen touches. The PENIRQ
output remains low until the fourth falling edge of DCLK after
the START bit is clocked in, at which point it returns high as
soon as possible, irrespective of the touch screen capacitance.
This does not mean that the pen interrupt function is now
enabled again because the power-down bits have not yet been
loaded to the control register. Regardless of whether PENIRQ is
to be enabled again, the PENIRQ output normally always idles
high. Assuming the PENIRQ is enabled again as shown in
Figure 34, then once the conversion is complete, the PENIRQ
output again responds to a screen touch. The fact that PENIRQ
returns high almost immediately after the fourth falling edge of
DCLK means the user avoids any spurious interrupts on the
microprocessor or DSP, which can occur if the interrupt request
line on the micro/DSP were unmasked during or toward the
end of conversion and the PENIRQ pin was still low. Once the
next start bit is detected by the AD7843, the PENIRQ function
is again disabled.
If the control register write operation overlaps with the data
read, a start bit is always detected prior to the end of
conversion, meaning that even if the PENIRQ function is
enabled in the control register, it is disabled by the start bit
again before the end of the conversion is reached, so
the PENIRQ function effectively cannot be used in this mode.
However, as conversions are occurring continuously,
the PENIRQ function is not necessary and is therefore
redundant.
Figure 33. PENIRQ Functional Block Diagram
Figure 34. PENIRQ Timing Diagram
Y+
Y–
ON
X+
TOUCH
SCREEN
EXTERNAL
PULL-UP
PENIRQ
ENABLE
+VCC
PENIRQ
100k
02164-
033
S
A2
A1
A0
1
0
8
1
13
16
MODE
SER/
DFR
SCREEN
TOUCHED
HERE
NO RESPONSE TO TOUCH
tPEN
PENIRQ
CS
DCLK
DIN
(START)
PD1 = 1, PD0 = 0, PENIRQ
ENABLED AGAIN
INTERRUPT
PROCESSOR
02164-
034
相關PDF資料 |
PDF描述 |
|---|---|
| M83723/76R1203N | CONN PLUG 3POS STRAIGHT W/PINS |
| MS27474E22A55SB | CONN RCPT 55POS JAM NUT W/SCKT |
| AD7873ARQZ-REEL7 | IC ADC 12BIT TOUCHSCREEN 16QSOP |
| VE-J5J-MX-F4 | CONVERTER MOD DC/DC 36V 75W |
| VE-J5J-MX-F3 | CONVERTER MOD DC/DC 36V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7874 | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS 4-Channel, 12-Bit Simultaneous Sampling Data Acquisition System |
| AD7874AN | 功能描述:IC DAS 12BIT 4CH LC2MOS 28-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD7874ANZ | 功能描述:IC DAS 12BIT 4CH LC2MOS 28-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Data Converter Basics 標準包裝:1 系列:- 類型:電機控制 分辨率（位）:12 b 采樣率（每秒）:1M 數據接口:串行，并聯 電壓電源:單電源 電源電壓:2.7 V ~ 3.6 V，4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:100-TQFP 供應商設備封裝:100-TQFP（14x14） 包裝:剪切帶 (CT) 其它名稱:296-18373-1 |
| AD7874ANZ | 制造商:Analog Devices 功能描述:IC 12-BIT ADC |
| AD7874AQ | 功能描述:IC DAS 12BIT 4CH 5V 28-CDIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。