參數資料
型號: AD7876CR-REEL
廠商: Analog Devices Inc
文件頁數: 15/28頁
文件大小: 0K
描述: IC ADC 12BIT SAMPLING 10V 24SOIC
產品變化通告: Conversion Time Change
標準包裝: 1,000
位數: 12
采樣率(每秒): 100k
數據接口: 串行,并聯
轉換器數目: 1
功率耗散(最大): 95mW
電壓電源: 雙 ±
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 24-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 24-SOIC W
包裝: 帶卷 (TR)
輸入數目和類型: 1 個單端,雙極
AD7870/AD7875/AD7876
Rev. C | Page 22 of 2
8
APPLICATIONS INFORMATION
Good printed circuit board (PCB) layout is as important as
the overall circuit design itself in achieving high speed analog-
to-digital performance. The designer has to be conscious of
noise both in the ADC itself and in the preceding analog
circuitry. Switching mode power supplies are not recommended
because the switching spikes feed through to the comparator
causing noisy code transitions. Other causes of concern are
ground loops and digital feedthrough from microprocessors.
These are factors which influence any ADC, and a proper
PCB layout which minimizes these effects is essential for best
performance.
LAYOUT HINTS
Ensure that the layout for the printed circuit board has the
digital and analog signal lines separated as much as possible.
Take care not to run any digital track alongside an analog signal
track. Guard (screen) the analog input with AGND.
Establish a single point analog ground (star ground) separate
from the logic system ground at the AGND pin or as close
as possible to the ADC. Connect all other grounds and the
AD7870/AD7875/AD7876 DGND to this single analog
ground point. Do not connect any other digital grounds to
this analog ground point.
Low impedance analog and digital power supply common
returns are essential to low noise operation of the ADC, so
make the foil width for these tracks as wide as possible. The
use of ground planes minimizes impedance paths and also
guards the analog circuitry from digital noise. The circuit
layout has both analog and digital ground planes which are
kept separated and only joined together at the AD7870/
AD7875/AD7876 AGND pin.
NOISE
Keep the input signal leads to VIN and signal return leads from
AGND as short as possible to minimize input noise coupling.
In applications where this is not possible, use a shielded cable
between the source and the ADC. Reduce the ground circuit
impedance as much as possible since any potential difference
in grounds between the signal source and the ADC appears as
an error voltage in series with the input signal.
相關PDF資料
PDF描述
AD976ABRZRL IC ADC 16BIT 200KSPS 28SOIC
MS27474T20A41S CONN RCPT 41POS JAM NUT W/SCKT
MS27473T22A55S CONN PLUG 55POS STRAIGHT W/SCKT
AD7572AAR03 IC ADC 12BIT HS LC2MOS 24-SOIC
LTC491IS#TR IC TXRX RS485 LOW POWER 14-SOIC
相關代理商/技術參數
參數描述
AD7876CRZ 功能描述:IC ADC 12BIT SAMPLING 10V 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極
AD7876CRZ1 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete, 12-Bit, 100 kHz, Sampling ADCs
AD7876TQ 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel/Serial 24-Pin CDIP 制造商:Analog Devices 功能描述:ADC SGL SAR 100KSPS 12-BIT PARALLEL/SERL 24CDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:12-BIT SAMPLING ADC IC - Bulk 制造商:Analog Devices 功能描述:IC ADC 12BIT SAMPLING 10V 24CDIP 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC 12-BIT SAMPLING ADC IC 制造商:Analog Devices 功能描述:CONVERTER - ADC
AD7876TQ/883B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter, 12-Bit
AD7877 制造商:AD 制造商全稱:Analog Devices 功能描述:Touch Screen Controller