- 您現在的位置：買賣IC網 > PDF目錄10039 > AD7878LN (Analog Devices Inc)IC ADC 12BIT W/DSP INT 28-DIP PDF資料下載
參數資料
| 型號： | AD7878LN |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT W/DSP INT 28-DIP |
| 標準包裝： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 100k |
| 數據接口： | DSP |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 95.5mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 28-DIP（0.600"，15.24mm） |
| 供應商設備封裝： | 28-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個單端，雙極 |
AD7878
–4–
REV. A
PIN FUNCTION DESCRIPTION
Pin
Number
Mnemonic
Function
11
ADD0
Address Input. This control input determines whether the word placed on the output data bus during a read operation is a data
word from the FIFO RAM or the contents of the status/control register. A logic low accesses the data word from Location 0 of
the FIFO while a logic high selects the contents of the register (see Status/Control Register section).
12
CS
Chip Select. Active low logic input. The device is selected when this input is active.
13
DMWR
Dam Memory Write. Active low logic input.
DMWR is used in conjunction with CS low and ADD0 high to write data to the
status/control register. Corresponds to
DMWR (ADSP-2100), R/W (MC68000, TMS32020), WE (TMS32010).
14
DMRD
Data Memory READ. Active low logic input.
DMRD is used in conjunction with CS low to enable the three-state output buffers.
Corresponds directly to
DMRD (ADSP-2100), DEN (TMS32010).
15
BUSY
Active Low Logic Output. This output goes low when the ADC receives a
CONVST pulse and remains low until the track/hold
has gone into its hold mode. The three-state drivers of the AD7878 can be disabled while the
BUSY signal is low (see Extended
READ/WRITE section). This is achieved by writing a logic 0 to DB5 (
DISO) of the status/control register. Writing a logic 1 to
DB5 of the status/control register allows data to be accessed from the AD7878 while BUSY is low.
16
ALFL
FIFO Almost Full. A logic low indicates that the word count (i.e., number of conversion results) in the FIFO memory has
reached the programmed word count in the status/control register.
ALFL is updated at the end of each conversion. The ALFL
output is reset to a logic high when a word is read from the FIFO memory and the word count is less than the preprogrammed
word count. It can also be set high by writing a logic 1 to DB7 (
ENAF) of the status/control register.
17
DGND
Digital Ground. Ground reference for digital circuitry.
18VCC
Digital supply voltage, +5 V
± 5%. Positive supply voltage for digital circuitry.
19
DB11
Data Bit 11 (MSB). Three-state TTL output. Coding for the data words in FIFO RAM is twos complement.
10–15
DB10–DB5
Data Bit 10 to Data Bit 5. Three-state TTL input/outputs.
16–19
DB4–DB1
Data Bit 4 to Data Bit 1. Three-state TTL outputs.
20
DB0
Data Bit 0 (LSB). Three-state TTL output.
21
VDD
Analog positive supply voltage, +5 V
± 5%.
22
AGND
Analog Ground. Ground reference for track/hold, reference and DAC.
23
REF OUT
Voltage Reference Output. The internal 3 V analog reference is provided at this pin. The external load capability of the reference
is 500
A.
24
VIN
Analog Input. Analog input range is
±3 V.
25
VSS
Analog negative supply voltage, –5 V
± 5%.
26
CONVST
Convert Start. Logic input. A low to high transition on this input puts the track/hold into its hold mode and starts conversion.
The
CONVST input is asynchronous to CLK IN and independent of CS, DMWR and DMRD.
27
RESET
Reset. Active low logic input. A logic low sets the words in FIFO memory to 1000 0000 0000 and resets the
ALFL output and
status/control register.
28
CLK IN
Clock Input. TTL-compatible logic input. Used as the clock source for the A/D converter. The mark-space ratio of this clock can
vary from 35/65 to 65/35.
PIN CONFIGURATIONS
LCCC
PLCC
DIP
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B6T-MW-F1 | CONVERTER MOD DC/DC 6.5V 100W |
| MS27484T18F11S | CONN PLUG 11POS STRAIGHT W/SCKT |
| MS27466P9A35S | CONN RCPT 6POS WALL MNT W/SCKT |
| IDT72V831L20PF8 | IC SYNC FIFO 2048X9 20NS 64QFP |
| VI-BNL-IV-F3 | CONVERTER MOD DC/DC 28V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7878LP | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel 28-Pin PLCC 制造商:Rochester Electronics LLC 功能描述:12-BIT ADC IC - Bulk |
| AD7878LPZ | 功能描述:IC ADC 12BIT W/DSP INT 28-PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極 |
| AD7878LPZ-REEL | 功能描述:IC ADC 12BIT W/DSP 28PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7878SE | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878SE/883B | 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12-BIT ADC IC - Bulk 制造商:Analog Devices 功能描述:CONVERTER - ADC |
發布緊急采購，3分鐘左右您將得到回復。