- 您現在的位置：買賣IC網 > PDF目錄373926 > AD7921ARM-REEL (ANALOG DEVICES INC) 2-Channel, 2.35 V to 5.25 V 250 kSPS, 10-/12-Bit ADCs PDF資料下載
參數資料
| 型號： | AD7921ARM-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 2-Channel, 2.35 V to 5.25 V 250 kSPS, 10-/12-Bit ADCs |
| 中文描述： | 2-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| 封裝： | MO-187AA, MSOP-8 |
| 文件頁數： | 18/28頁 |
| 文件大?。?/td> | 312K |
| 代理商： | AD7921ARM-REEL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7911/AD7921
MODES OF OPERATION
The two modes of operation of the AD7911/AD7921 are
normal mode and power-down mode. The mode of operation is
selected by controlling the logic state of the CS signal. The point
at which CS is pulled high after the conversion has been initi-
ated determines whether the AD7911/AD7921 enter power-
down mode. Similarly, if already in power-down mode, CS can
control whether the device returns to normal operation or
remains in power-down mode.
Rev. 0 | Page 18 of 28
Power-down mode is designed to provide flexible power
management options and to optimize the ratio of power
dissipation to throughput rate for different application
requirements.
NORMAL MODE
Normal mode is intended for the fastest throughput rate
performance. The user does not have to worry about any
power-up time, because the AD7911/AD7921 remain fully
powered all the time. Figure 26 shows the operation of the
AD7911/AD7921 in this mode.
The conversion is initiated on the falling edge of CS, as
described in the Serial Interface section. To ensure that the part
remains fully powered up at all times, CS must remain low until
at least 10 SCLK falling edges have elapsed after the falling edge
of CS. If CS is brought high any time after the 10th SCLK falling
edge but before the end of t
CONVERT
, the part remains powered-
up, but the conversion is terminated and DOUT goes back into
three-state. For the AD7911/AD7921, a minimum of 14 and
16 serial clock cycles, respectively, are needed to complete the
conversion and access the complete conversion result.
CS can idle high until the next conversion or can idle low until
CS returns high sometime prior to the next conversion
(effectively idling CS low). Once a data transfer is complete
(DOUT has returned to three-state), another conversion can be
initiated after the quiet time, t
QUIET
, has elapsed by bringing CS
low again.
POWER-DOWN MODE
Power-down mode is intended for use in applications where
slower throughput rates are required. Either the ADC is
powered down between each conversion, or a series of
conversions can be performed at a high throughput rate and
then the ADC is powered down for a relatively long duration
between these bursts of several conversions. When the
AD7911/AD7921 are in power-down mode, all analog circuitry
is powered down.
To enter power-down mode, the conversion process must be
interrupted by bringing CS high any time after the second
falling edge of SCLK and before the 10th falling edge of SCLK,
as shown in Figure 27. Once CS has been brought high in this
window of SCLKs, then the part enters power-down mode, the
conversion that was initiated by the falling edge of CS is
terminated, and DOUT goes back into three-state. If CS is
brought high before the second SCLK falling edge, then the part
remains in normal mode and does not power down. This helps
to avoid accidental power-down due to glitches on the CS line.
To exit this mode of operation and power the AD7911/AD7921
up again, a dummy conversion is performed. On the falling edge
of CS, the device begins to power up and continues to power up
as long as CS is held low until after the falling edge of the 10th
SCLK. The device is fully powered up once 16 SCLKs have
elapsed and valid data results from the next conversion, as
shown in Figure 28. If CS is brought high before the 10th falling
edge of SCLK, then the AD7911/AD7921 go back into power-
down mode. This helps to avoid accidental power-up due to
glitches on the CS line or an inadvertent burst of 8 SCLK cycles
while CS is low. Therefore, although the device might begin to
power up on the falling edge of CS, it powers down again on the
rising edge of CS, as long as this occurs before the 10th SCLK
falling edge.
0
CS
1
10
12
14
16
1
10
12
14
16
AD7911/AD7921
SCLK
DIN
DOUT
CHANNEL FOR NEXT CONVERSION
CHANNEL FOR NEXT CONVERSION
CONVERSION RESULT
CONVERSION RESULT
Figure 26. Normal Mode Operation
相關PDF資料 |
PDF描述 |
|---|---|
| AD7921ARM-REEL7 | 2-Channel, 2.35 V to 5.25 V 250 kSPS, 10-/12-Bit ADCs |
| AD7921AUJ-R2 | 2-Channel, 2.35 V to 5.25 V 250 kSPS, 10-/12-Bit ADCs |
| AD7921AUJ-REEL7 | 2-Channel, 2.35 V to 5.25 V 250 kSPS, 10-/12-Bit ADCs |
| AD7911 | 2-Channel, 2.35 V to 5.25 V 250 kSPS, 10-/12-Bit ADCs |
| AD7922AUJ-R2 | ER 2C 2#16S PIN RECP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7921ARM-REEL7 | 功能描述:IC ADC 12BIT DUAL LP 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7921ARMZ | 功能描述:IC ADC 12BIT DUAL LP 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7921ARMZ-REEL | 功能描述:IC ADC 12BIT DUAL LP 8MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD7921ARMZ-REEL7 | 功能描述:IC ADC 12BIT DUAL LP 8MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7921AUJ-R2 | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述:DUAL 12-BIT , 250KSPS ADC I.C. - Bulk |
發布緊急采購，3分鐘左右您將得到回復。