- 您現在的位置：買賣IC網 > PDF目錄1985 > AD7951BSTZRL (Analog Devices Inc)IC ADC 14BIT 1MSPS 48-LQFP PDF資料下載
參數資料
| 型號： | AD7951BSTZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 14/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT 1MSPS 48-LQFP |
| 標準包裝： | 2,000 |
| 系列： | PulSAR® |
| 位數： | 14 |
| 采樣率（每秒）： | 1M |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 260mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD7951
Rev. A | Page 21 of 32
DRIVER AMPLIFIER CHOICE
Although the AD7951 is easy to drive, the driver amplifier must
meet the following requirements:
For multichannel, multiplexed applications, the driver
amplifier and the AD7951 analog input circuit must be
able to settle for a full-scale step of the capacitor array at a
14-bit level (0.006%). For the amplifier, settling at 0.1% to
0.01% is more commonly specified. This differs significantly
from the settling time at a 14-bit level and should be
verified prior to driver selection. The AD8021 op amp com-
bines ultralow noise and high gain bandwidth and meets
this settling time requirement even when used with gains
of up to 13.
The noise generated by the driver amplifier needs to be
kept as low as possible to preserve the SNR and transition
noise performance of the AD7951. The noise coming from
the driver is filtered by the external one-pole low-pass filter
as shown in Figure 27. The SNR degradation due to the
amplifier is
2
3
2
log
20
N
dB
NADC
LOSS
Ne
f
V
SNR
where:
VNADC is the noise of the ADC, which is:
20
10
2
SNR
INp-p
NADC
V
f–3dB is the cutoff frequency of the input filter (3.9 MHz).
N is the noise factor of the amplifier (+1 in buffer
configuration).
eN is the equivalent input voltage noise density of the op
amp, in nV/√Hz.
The driver needs to have a THD performance suitable to
that of the AD7951. Figure 15 shows the THD vs. frequency
that the driver should exceed.
The AD8021 meets these requirements and is appropriate for
almost all applications. The AD8021 needs a 10 pF external
compensation capacitor that should have good linearity as an
NPO ceramic or mica type. Moreover, the use of a noninverting
+1 gain arrangement is recommended and helps to obtain the
best signal-to-noise ratio.
The AD8022 can also be used when a dual version is needed
and a gain of 1 is present. The AD829 is an alternative in applica-
tions where high frequency (above 100 kHz) performance is not
required. In applications with a gain of 1, an 82 pF compensation
capacitor is required. The AD8610 is an option when low bias
current is needed in low frequency applications.
Since the AD7951 uses a large geometry, high voltage input
switch, the best linearity performance is obtained when using
the amplifier at its maximum full power bandwidth. Gaining
the amplifier to make use of the more dynamic range of the
ADC results in increased linearity errors. For applications
requiring more resolution, the use of an additional amplifier
with gain should precede a unity follower driving the AD7951.
See Table 8 for a list of recommended op amps.
Table 8. Recommended Driver Amplifiers
Amplifier
Typical Application
12 V supply, very low noise, low distortion,
low power, low frequency
±15 V supplies, very low noise, low frequency
±12 V supplies, very low noise, high frequency
±12 V supplies, very low noise, high
frequency, dual
±13 V supplies, low bias current, low
frequency, single/dual
VOLTAGE REFERENCE INPUT/OUTPUT
The AD7951 allows the choice of either a very low temperature
drift internal voltage reference, an external reference, or an
external buffered reference.
The internal reference of the AD7951 provides excellent perform-
ance and can be used in almost all applications. However, the
linearity performance is guaranteed only with an external reference.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7952BCPZ | IC ADC 14BIT DIFF 1MSPS 48LFCSP |
| AD7980ARMZ | ADC 16BIT 1MSPS LP 10-MSOP |
| AD7982BCPZ-RL | IC ADC 18BIT 1MSPS PULSAR 10LFCS |
| AD7983BCPZ-RL7 | IC ADC 16BIT 1.33MSPS 10LFCSP |
| AD7984BCPZ-RL7 | IC ADC 18BIT 1.33MSPS 10LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7952 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 1 MSPS, Differential, Programmable Input PulSAR ADC |
| AD7952BCPZ | 功能描述:IC ADC 14BIT DIFF 1MSPS 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7952BCPZRL | 功能描述:IC ADC 14BIT DIFF 1MSPS 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7952BSTZ | 功能描述:IC ADC 14BIT DIFF 1MSPS 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7952BSTZRL | 功能描述:IC ADC 14BIT DIFF 1MSPS 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。