- 您現在的位置：買賣IC網 > PDF目錄10692 > AD7991YRJZ-1500RL7 (Analog Devices Inc)IC ADC 12BIT 4CH SAR I2C SOT23-8 PDF資料下載
參數資料
| 型號： | AD7991YRJZ-1500RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 15/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 4CH SAR I2C SOT23-8 |
| 產品變化通告： | AD7991,5,9 Offset Error Change 17/Sept/2010 |
| 設計資源： | Using AD8599 as an Ultralow Distortion Driver for the AD7991 (CN0043) |
| 標準包裝： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 1M |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 4.68mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-8 |
| 供應商設備封裝： | SOT-23-8 |
| 包裝： | 標準包裝 |
| 輸入數目和類型： | 4 個單端，單極 |
| 產品目錄頁面： | 780 (CN2011-ZH PDF) |
| 配用： | EVAL-AD7991EBZ-ND - BOARD EVAL FOR AD7991 |
| 其它名稱： | AD7991YRJZ-1500RL7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7991/AD7995/AD7999
Rev. B | Page 22 of 28
SERIAL INTERFACE
Control of the AD7991/AD7995/AD7999 is accomplished via
the I2C-compatible serial bus. The AD7991/AD7995/AD7999 is
connected to this bus as a slave device under the control of a
master device, such as the processor.
SERIAL BUS ADDRESS
Like all I2C-compatible devices, the AD7991/AD7995/AD7999 has
a 7-bit serial address. The devices are available in two versions, the
AD7991-0/AD7995-0 and the AD7991-1/AD7995-1/AD7999-1.
Each version has a different address (see Table 8), which allows up
to two AD7991/AD7995 devices to be connected to a single
serial bus. AD7999 has only one version.
The serial bus protocol operates as follows:
1.
The master initiates a data transfer by establishing a start
condition, defined as a high-to-low transition on the serial
data line SDA while the serial clock line, SCL, remains high.
This indicates that an address/data stream follows.
2.
All slave peripherals connected to the serial bus respond to
the start condition and shift in the next eight bits, consisting of
a 7-bit address (MSB first) plus an R/W bit that determines
the direction of the data transfer—that is, whether data is
written to or read from the slave device.
3.
The peripheral whose address corresponds to the transmitted
address responds by pulling the data line low during the
low period before the ninth clock pulse, known as the
acknowledge bit. All other devices on the bus remain idle
while the selected device waits for data to be read from or
written to it. If the R/W bit is set to 0, the master writes to
the slave device. If the R/W bit is set to 1, the master reads
from the slave device.
4.
Data is sent over the serial bus in sequences of nine clock
pulses—eight bits of data followed by an acknowledge bit
from the receiver of data. Transitions on the data line must
occur during the low period of the clock signal and remain
stable during the high period because a low-to-high transition
when the clock is high may be interpreted as a stop signal.
5.
When all data bytes have been read or written, stop conditions
are established. In write mode, the master pulls the data line
high during the 10th clock pulse to assert a stop condition.
In read mode, the master device pulls the data line high
during the low period before the ninth clock pulse. This is
known as a no acknowledge. The master takes the data line
low during the low period before the 10th clock pulse, and
then high during the 10th clock pulse to assert a stop condition.
6.
Any number of bytes of data can be transferred over the serial
bus in one operation, but it is not possible to mix reads and
writes in one operation because the type of operation is
determined at the beginning and cannot subsequently be
changed without starting a new operation.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1671IS8#TR | IC COMPARATOR 60NS LOW PWR 8SOIC |
| LTC1441IS8#PBF | IC COMP W/REF LP DUAL 8-SOIC |
| LTC1441IS8 | IC COMP W/REF LP DUAL 8-SOIC |
| CS5550-ISZ | IC ADC 2CH LOW-COST 24SSOP |
| VE-2W0-MY-B1 | CONVERTER MOD DC/DC 5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7991YRJZ-1RL | 功能描述:IC ADC 12BIT 4CH I2C SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7992 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2-Channel, 12-Bit ADC with I2C Compatible Interface in 10-Lead MSOP |
| AD7992_05 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2-Channel, 12-Bit ADC with I2C-Compatible |
| AD7992BRM-0 | 制造商:Analog Devices 功能描述:ADC Single SAR 188ksps 12-bit Serial 10-Pin MSOP |
| AD7992BRM-0REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 188ksps 12-bit Serial 10-Pin MSOP T/R |
發布緊急采購，3分鐘左右您將得到回復。