- 您現在的位置：買賣IC網 > PDF目錄10547 > AD7993BRUZ-1 (Analog Devices Inc)IC ADC 10BIT 4CHAN I2C 16TSSOP PDF資料下載
參數資料
| 型號： | AD7993BRUZ-1 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 21/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 4CHAN I2C 16TSSOP |
| 標準包裝： | 96 |
| 位數： | 10 |
| 采樣率（每秒）： | 188k |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 2.2mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7993/AD7994
Rev. 0 | Page 28 of 32
MODES OF OPERATION
When supplies are first applied to the AD7993/AD7994, the
ADC powers up in shutdown mode and normally remains in
this shutdown state while not converting. There are three
different methods of initiating a conversion on the devices.
MODE 1—USING THE CONVST PIN
A conversion can be initiated on the AD7993/AD7994 by
pulsing the CONVST signal. The conversion clock for the part
is internally generated so no external clock is required, except
when reading from or writing to the I2C interface. On the rising
edge of CONVST, the AD7993/AD7994 begin to power up
(see Point A in Figure 32). The power-up time from shutdown
mode for the AD7993/AD7994 is approximately 1 s; the
CONVST signal must remain high for 1 s for the part to power
up fully. CONVST can be brought low after this time. The
falling edge of the CONVST signal places the track-and-hold
into hold mode; a conversion is also initiated at this point
(Point B in Figure 32). When the conversion is complete,
approximately 2 s later, the parts return to shutdown (Point C
in Figure 32) and remain there until the next rising edge of
CONVST. The master can then read the ADC to obtain the
conversion result. The address pointer register must be pointing
to the conversion result register in order to read back the
conversion result.
If the CONVST pulse does not remain high for more than 1 s,
the falling edge of CONVST still initiates a conversion but the
result is invalid because the AD7993/AD7994 are not fully
powered up when the conversion takes place. To maintain the
performance of the AD7993/AD7994 in this mode it is
recommended that the I2C bus is quiet when a conversion is
taking place.
The cycle timer register and Bits C4 to C1 in the address pointer
register should contain all 0s when operating the AD7994/
AD7993 in this mode. The CONVST pin should be tied low for
all other modes of operation. To select an analog input channel
for conversion in this mode, the user must write to the
configuration register and select the corresponding channel for
conversion. To set up a sequence of channels to be converted
with each CONVST pulse, set the corresponding channel bits in
the configuration register (see Table 11).
Once the conversion is complete, the master can address the
AD7993/AD7994 to read the conversion result. If further
conversions are required, the SCL line can be taken high while
the CONVST signal is pulsed again; then an additional 18 SCL
pulses are required to read the conversion result.
When operating the AD7993-1/AD7994-1 in Mode 1 and
reading after the conversion with a 3.4 MHz SCL, the ADCs can
achieve a throughput rate of up to 121 kSPS.
11
9
SCA
9
S
7-BIT ADDRESS
RA
FIRST DATA BYTE (MSBs)
A
SECOND DATA BYTE (LSBs)
9
P
SDA
tPOWER-UP
B
A
C
tCONVERT
03472-0-032
CONVST
A
Figure 32. Mode 1 Operation
相關PDF資料 |
PDF描述 |
|---|---|
| VI-25Y-IU-F4 | CONVERTER MOD DC/DC 3.3V 132W |
| LTC1199CS8#PBF | IC ADC 10BIT 450KHZ W/SD 8-SOIC |
| LTC1199LCS8#PBF | IC ADC 10BIT 210KHZ W/SD 8-SOIC |
| VI-25Y-IU-F3 | CONVERTER MOD DC/DC 3.3V 132W |
| AD7278BRMZ | IC ADC 8BIT 3MSPS HS LP 8MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7993BRUZ-1REEL | 功能描述:IC ADC 10BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7993-X | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 10- and 12-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| AD7994 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| AD7994-0 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 10- and 12-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
| AD7994-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 10- and 12-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP |
發布緊急采購，3分鐘左右您將得到回復。