- 您現在的位置：買賣IC網 > PDF目錄6046 > AD8008ARMZ (Analog Devices Inc)IC OPAMP CF DUAL ULDIST LN 8MSOP PDF資料下載
參數資料
| 型號： | AD8008ARMZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/21頁 |
| 文件大小： | 0K |
| 描述： | IC OPAMP CF DUAL ULDIST LN 8MSOP |
| 標準包裝： | 50 |
| 放大器類型： | 電流反饋 |
| 電路數： | 2 |
| 轉換速率： | 1000 V/µs |
| -3db帶寬： | 650MHz |
| 電流 - 輸入偏壓： | 4µA |
| 電壓 - 輸入偏移： | 500µV |
| 電流 - 電源： | 9mA |
| 電流 - 輸出 / 通道： | 130mA |
| 電壓 - 電源，單路/雙路(±)： | 5 V ~ 12 V，±2.5 V ~ 6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 管件 |
| 產品目錄頁面： | 769 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁
AD8007/AD8008
Rev. E | Page 17 of
20
LAYOUT AND GROUNDING CONSIDERATIONS
GROUNDING
A ground plane layer is important in densely packed printed
circuit boards (PCB) to minimize parasitic inductances. However,
an understanding of where the current flows in a circuit is critical
to implementing effective high speed circuit design. The length
of the current path is directly proportional to the magnitude of
parasitic inductances and thus the high frequency impedance of
the path. High speed currents in an inductive ground return
create unwanted voltage noise. Broad ground plane areas reduce
parasitic inductance.
INPUT CAPACITANCE
Along with bypassing and ground, high speed amplifiers can be
sensitive to parasitic capacitance between the inputs and ground.
Even 1 pF or 2 pF of capacitance reduces the input impedance at
high frequencies, in turn increasing the gain of the amplifier, which
causes peaking of the frequency response or even oscillations if
severe enough. Place the external passive components that are
connected to the input pins as close as possible to the inputs to
avoid parasitic capacitance. The ground and power planes must
be kept at a distance of at least 0.05 mm from the input pins on
all layers of the board.
OUTPUT CAPACITANCE
To a lesser extent, parasitic capacitances on the output can cause
peaking of the frequency response. The following two methods
minimize its effect:
Put a small value resistor in series with the output to isolate
the load capacitance from the output stage of the amplifier
(see Figure 12).
Increase the phase margin by increasing the gain of the
amplifier or by increasing the value of the feedback resistor.
INPUT-TO-OUTPUT COUPLING
To minimize capacitive coupling, the input and output signal
traces should not be parallel. When they are not parallel, they
help reduce unwanted positive feedback.
EXTERNAL COMPONENTS AND STABILITY
The AD8007/AD8008 are current feedback amplifiers and, to a
first order, the feedback resistor determines the bandwidth and
stability. The gain, load impedance, supply voltage, and input
impedances also have an effect.
peaking for a gain of 2. Increasing RF reduces peaking but also
the gain also reduces peaking and bandwidth. Table 4 shows the
recommended RF and RG values that optimize bandwidth with
minimal peaking.
Table 4. Recommended Component Values
Gain
RF (Ω)
RG (Ω)
RS (Ω)
1
499
200
+1
499
Not applicable
200
+2
499
200
+5
499
124
200
+10
499
54.9
200
The load resistor also affects bandwidth, as shown in Figure 7 and
demonstrates the effect of gain and supply voltage.
When driving loads with a capacitive component, stability
improves by using a series snub resistor, RSNUB, at the output.
The frequency and pulse responses for various capacitive
For noninverting configurations, a resistor in series with the
input, RS, is needed to optimize stability for a gain of 1, as
illustrated in Figure 8. For larger noninverting gains, the effect
of a series resistor is reduced.
相關PDF資料 |
PDF描述 |
|---|---|
| ADEL2020ANZ | IC OPAMP CF LN LP 60MA 8DIP |
| AD8017ARZ | IC AMP GP DUAL LP LDIST 8SOIC |
| SMCJ36CA | TVS BIDIRECT 36V 1500W SMC |
| PEC02DAFN | CONN HEADER .100 DUAL STR 4POS |
| AD706ARZ | IC OPAMP GP DUAL PREC 15MA 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8008ARMZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultralow Distortion,High Speed Amplifiers |
| AD8008ARMZ-REEL | 功能描述:IC OPAMP CF DUAL ULDIST LN 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR |
| AD8008ARMZ-REEL1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultralow Distortion,High Speed Amplifiers |
| AD8008ARMZ-REEL7 | 功能描述:IC OPAMP CF DUAL ULDIST LN 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:電流檢測 電路數:1 輸出類型:- 轉換速率:- 增益帶寬積:125kHz -3db帶寬:- 電流 - 輸入偏壓:- 電壓 - 輸入偏移:100µV 電流 - 電源:1.1µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:4-WFBGA，CSPBGA 供應商設備封裝:4-UCSP（2x2） 包裝:剪切帶 (CT) 其它名稱:MAX9634WERS+TCT |
| AD8008ARMZ-REEL71 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultralow Distortion,High Speed Amplifiers |
發布緊急采購，3分鐘左右您將得到回復。