參數資料
型號： AD8036AR
廠商： Analog Devices Inc
文件頁數： 8/24頁
文件大小： 0K
描述： IC OPAMP VF ULDIST LN 70MA 8SOIC
標準包裝： 1
系列： CLAMPIN™
放大器類型： 電壓反饋
電路數： 1
轉換速率： 1200 V/µs
-3db帶寬： 240MHz
電流 - 輸入偏壓： 4µA
電壓 - 輸入偏移： 2000µV
電流 - 電源： 20.5mA
電流 - 輸出 / 通道： 70mA
電壓 - 電源，單路/雙路(±)： ±3 V ~ 6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 8-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 8-SOIC
包裝： 管件
配用： AD8036-EB-ND - BOARD EVAL FOR AD8036
AD8036/AD8037
REV. B
–15–
THEORY OF OPERATION
General
The AD8036 and AD8037 are wide bandwidth, voltage feedback
clamp amplifiers. Since their open-loop frequency response fol-
lows the conventional 6 dB/octave roll-off, their gain bandwidth
product is basically constant. Increasing their closed-loop gain
results in a corresponding decrease in small signal bandwidth. This
can be observed by noting the bandwidth specification, between
the AD8036 (gain of 1) and AD8037 (gain of 2). The AD8036/
AD8037 typically maintain 65 degrees of phase margin. This
high margin minimizes the effects of signal and noise peaking.
While the AD8036 and AD8037 can be used in either an invert-
ing or noninverting configuration, the clamp function will only
work in the noninverting mode. As such, this section shows con-
nections only in the noninverting configuration. Applications
that require an inverting configuration will be discussed in the
Applications section. In applications that do not require clamp-
ing, Pins 5 and 8 (respectively VL and VH) may be left floating.
See Input Clamp Amp Operation and Applications sections
otherwise.
Feedback Resistor Choice
The value of the feedback resistor is critical for optimum perfor-
mance on the AD8036 (gain +1) and less critical as the gain
increases. Therefore, this section is specifically targeted at
the AD8036.
At minimum stable gain (+1), the AD8036 provides optimum
dynamic performance with RF = 140
. This resistor acts only
as a parasitic suppressor against damped RF oscillations that
can occur due to lead (input, feedback) inductance and parasitic
capacitance. This value of RF provides the best combination of
wide bandwidth, low parasitic peaking, and fast settling time.
In fact, for the same reasons, a 100–130
resistor should be
placed in series with the positive input for other AD8036 non-
inverting configurations. The correct connection is shown in
Figure 3.
RF
100 - 130
RTERM
RF
RG
G = 1+
RG
VH
VL
+VS
–VS
VIN
VOUT
0.1 F
10 F
0.1 F
10 F
AD8036/
AD8037
Figure 3. Noninverting Operation
For general voltage gain applications, the amplifier bandwidth
can be closely estimated as:
f
3 dB
ω
O
2
π 1+
R
F
R
G
This estimation loses accuracy for gains of +2/–1 or lower due
to the amplifier’s damping factor. For these “l(fā)ow gain” cases,
the bandwidth will actually extend beyond the calculated value
(see Closed-Loop BW plots, TPCs 13 and 25).
Pulse Response
Unlike a traditional voltage feedback amplifier, where the slew
speed is dictated by its front end dc quiescent current and gain
bandwidth product, the AD8036 and AD8037 provide “on
demand” current that increases proportionally to the input
“step” signal amplitude. This results in slew rates (1200 V/
s)
comparable to wideband current feedback designs. This, com-
bined with relatively low input noise current (2.1 pA/
√Hz), gives
the AD8036 and AD8037 the best attributes of both voltage and
current feedback amplifiers.
Large Signal Performance
The outstanding large signal operation of the AD8036 and
AD8037 is due to a unique, proprietary design architecture.
In order to maintain this level of performance, the maximum
350 V-MHz product must be observed, (e.g., @ 100 MHz,
VO
≤ 3.5 V p-p).
Power Supply and Input Clamp Bypassing
Adequate power supply bypassing can be critical when optimiz-
ing the performance of a high frequency circuit. Inductance in
the power supply leads can form resonant circuits that produce
peaking in the amplifier’s response. In addition, if large current
transients must be delivered to the load, then bypass capacitors
(typically greater than 1
F) will be required to provide the best
settling time and lowest distortion. A parallel combination of at
least 4.7
F, and between 0.1 F and 0.01 F, is recommended.
Some brands of electrolytic capacitors will require a small series
damping resistor
≈4.7 for optimum results.
When the AD8036 and AD8037 are used in clamping mode,
and a dc voltage is connected to clamp inputs VH and VL, a 0.1
F
bypassing capacitor is required between each input pin and
ground in order to maintain stability.
Driving Capacitive Loads
The AD8036 and AD8037 were designed primarily to drive
nonreactive loads. If driving loads with a capacitive compo-
nent is desired, the best frequency response is obtained by
the addition of a small series resistance as shown in Figure 4.
The accompanying graph shows the optimum value for RSERIES
vs. capacitive load. It is worth noting that the frequency response
of the circuit when driving large capacitive loads will be domi-
nated by the passive roll-off of RSERIES and CL. For capacitive
loads of 6 pF or less, no RSERIES is necessary.
RL
1k
RF
RIN
RSERIES
CL
AD8036/
AD8037
RIN
Figure 4. Driving Capacitive Loads
相關PDF資料
PDF描述
AD848AQ IC OPAMP GP 175MHZ LP 32MA 8CDIP
142680-4 CONN RCPT HSG 2POS .197 YELLOW
RNCP0805FTD6K49 RES 6.49K OHM 1/4W 1% 0805 SMD
RNCP0805FTD100R RES 100 OHM 1/4W 1% 0805 SMD
142680 CONN RCPT HSG 2POS .197 BLACK
相關代理商/技術參數
參數描述
AD8036AR-REEL 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk
AD8036AR-REEL7 功能描述:IC OPAMP VF ULDIST LN 70MA 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:CLAMPIN™ 標準包裝:150 系列:- 放大器類型:音頻 電路數:2 輸出類型:- 轉換速率:5 V/µs 增益帶寬積:12MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:500µV 電流 - 電源:6mA 電流 - 輸出 / 通道:50mA 電壓 - 電源，單路/雙路(±):4 V ~ 32 V，±2 V ~ 16 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件
AD8036ARZ 功能描述:IC OPAMP VF ULDIST LN 70MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:CLAMPIN™ 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR
AD8036ARZ 制造商:Analog Devices 功能描述:IC OP-AMP 240MHZ 1200V/ SOIC-8
AD8036ARZ-REEL 功能描述:IC OPAMP VF ULDIST LN 70MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:CLAMPIN™ 標準包裝:150 系列:- 放大器類型:音頻 電路數:2 輸出類型:- 轉換速率:5 V/µs 增益帶寬積:12MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:500µV 電流 - 電源:6mA 電流 - 輸出 / 通道:50mA 電壓 - 電源，單路/雙路(±):4 V ~ 32 V，±2 V ~ 16 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*