- 您現在的位置：買賣IC網 > PDF目錄5298 > AD8056ARZ-REEL7 (Analog Devices Inc)IC OPAMP VF DUAL LDIST LN 8SOIC PDF資料下載
參數資料
| 型號： | AD8056ARZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/17頁 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VF DUAL LDIST LN 8SOIC |
| 標準包裝： | 1,000 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 2 |
| 轉換速率： | 1400 V/µs |
| -3db帶寬： | 300MHz |
| 電流 - 輸入偏壓： | 400nA |
| 電壓 - 輸入偏移： | 3000µV |
| 電流 - 電源： | 5.4mA |
| 電流 - 輸出 / 通道： | 60mA |
| 電壓 - 電源，單路/雙路(±)： | 8 V ~ 12 V，±4 V ~ 6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
AD8055/AD8056
Rev. J | Page 12 of 16
APPLICATIONS
FOUR-LINE VIDEO DRIVER
Between these points, a feedback resistor can be used to close
the loop. As in the case of a conventional op amp inverting gain
stage, an input resistor is added to vary the gain.
The AD8055 is a useful low cost circuit for driving up to four
video lines. For such an application, the amplifier is configured
for a noninverting gain of 2, as shown in Figure 36. The input
video source is terminated in 75 Ω and is applied to the high
impedance noninverting input.
/R
The gain of this circuit from the input to AMP1 output is RF I,
while the gain to the output of AMP2 is R /R
F
I
. The circuit
therefore creates a balanced differential output signal from a
single-ended input. The advantage of this circuit is that the gain
can be changed by changing a single resistor, while still
maintaining the balanced differential outputs.
Each output cable is connected to the op amp output via a 75 Ω
series back termination resistor for proper cable termination.
The terminating resistors at the other ends of the lines divide
the output signal by 2, which is compensated for by the gain of 2
of the op amp stage.
75
+5V
–5V
AD8056
402
49.9
1
2
3
8
AMP1
5
6
7
4
AMP2
0.1F
RF
402
RI
402
10F
0.1F
10F
VIN
+VOUT
–VOUT
01
06
3-
0
37
For a single load, the differential gain error of this circuit was
measured as 0.01%, with a differential phase error of 0.02°. The
two load measurements were 0.02% and 0.03°, respectively. For
four loads, the differential gain error is 0.02%, while the
differential phase increases to 0.1°.
VOUT3
AD8055
+5V
–5V
6
7
2
3
4
75
VOUT1
VOUT2
VOUT4
0.1F
10F
75
402
VIN
010
63-
036
Figure 37. Single-Ended-to-Differential Line Driver
Figure 36. Four-Line Video Driver
LOW NOISE, LOW POWER PREAMP
SINGLE-ENDED-TO-DIFFERENTIAL LINE DRIVER
The AD8055 makes a good, low cost, low noise, low power
preamp. A gain-of-10 preamp can be made with a feedback
resistor of 909 Ω and a gain resistor of 100 Ω, as shown in
Creating differential signals from single-ended signals is
required for driving balanced, twisted pair cables, differential
input ADCs, and other applications that require differential
signals. This can be accomplished by using an inverting and a
noninverting amplifier stage to create the complementary
signals.
Figure 38. The circuit has a 3 dB bandwidth of 20 MHz.
0.1F
10F
0.1F
10F
+5V
–5V
+
AD8055 6
7
2
3
4
VOUT
RS
909
100
0
10
63
-03
8
The circuit shown in Figure 37 shows how an AD8056 can be
used to make a single-ended-to-differential converter that offers
some advantages over the architecture previously mentioned.
Each op amp is configured for unity gain by the feedback
resistors from the outputs to the inverting inputs. In addition,
each output drives the opposite op amp with a gain of 1 by
means of the crossed resistors. The result of this is that the
outputs are complementary and there is high gain in the overall
configuration.
Figure 38. Low Noise, Low Power Preamp with G = +10 and BW = 20 MHz
With a low source resistance (< approximately 100 Ω), the
major contributors to the input-referred noise of this circuit are
the input voltage noise of the amplifier and the noise of the
100 Ω resistor. These are 6 nV/√Hz and 1.2 nV/√Hz, respectively.
These values yield a total input referred noise of 6.1 nV/√Hz.
Feedback techniques similar to a conventional op amp are used
to control the gain of the circuit. From the noninverting input
of AMP1 to the output of AMP2 is an inverting gain.
相關PDF資料 |
PDF描述 |
|---|---|
| TA35-CBDWM060C0 | CIRC BREAKER/WHITE ROCKER 2P 6A |
| AVR-M1005C080MTACB | VARISTOR 8V 1A 33PF 0402 SMD |
| TA35-CBDWM040C0 | CIRC BREAKER/WHITE ROCKER 2P 4A |
| TA35-CBDBH100C0 | CIRC BREAKER/BLACK ROCKER 2P 10A |
| AVR-M1005C270MTAAB | VARISTOR 27V 4A 40PF 0402 SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8057 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, High Performance Voltage Feedback, 325 MHz Amplifiers |
| AD8057_03 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, High Performance Voltage Feedback, 325 MHz Amplifiers |
| AD8057ACHIPS | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, High Performance Voltage Feedback, 325 MHz Amplifiers |
| AD8057AR | 功能描述:IC OPAMP VF LN LP LDIST 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| AD8057AR-EBZ | 功能描述:BOARD EVAL FOR AD8057AR RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
發布緊急采購，3分鐘左右您將得到回復。