- 您現在的位置：買賣IC網 > PDF目錄8541 > AD8073JRZ-REEL (Analog Devices Inc)IC VIDEO AMP TRIPLE 14-SOIC PDF資料下載
參數資料
| 型號： | AD8073JRZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 3/13頁 |
| 文件大小： | 0K |
| 描述： | IC VIDEO AMP TRIPLE 14-SOIC |
| 標準包裝： | 2,500 |
| 應用： | 電流反饋 |
| 電路數： | 3 |
| -3db帶寬： | 100MHz |
| 轉換速率： | 500 V/µs |
| 電流 - 電源： | 3.5mA |
| 電流 - 輸出 / 通道： | 30mA |
| 電壓 - 電源，單路/雙路(±)： | 5 V ~ 12 V，±2.5 V ~ 6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOICN |
| 包裝： | 帶卷 (TR) |
REV. D
AD8072/AD8073
–10–
Crosstalk
Crosstalk between internal amplifiers may vary depending on
which amplifier is being driven and how many amplifiers are
being driven. This variation typically stems from pin location on
the package and the internal layout of the IC itself. Table I
illustrates the typical crosstalk results for a combination of
conditions.
Table I. AD8073JR Crosstalk Table (dB)
Receive Amplifier
AD8073JR
12
3
1
X
–60
–56
Drive
2
–60
X
–60
Amplifier
3
–54
–60
X
All Hostile
–53
–55
–54
CONDITIONS
VS =
±5 V
RF = 1 k
, R
L = 150
AV = 2
VOUT = 2 V p-p on Drive Amplifier
Layout Considerations
The specified high speed performance of the AD8072 and
AD8073 require careful attention to board layout and compo-
nent selection. Proper RF design techniques and low parasitic
component selection are mandatory.
The PCB should have a ground plane covering all unused portions
of the component side of the board to provide a low impedance
ground path. The ground plane should be removed from the
area near the input pins to reduce stray capacitance.
Chip capacitors should be used for supply bypassing. One end
of the capacitor should be connected to the ground plane and
the other within 1/8 inches of each power pin. An additional
large (4.7
F–10 F) tantalum electrolytic capacitor should be
connected in parallel, but not necessarily as close to the supply
pins, to provide current for fast large-signal changes at the
device’s output.
The feedback resistor should be located close to the inverting
input pin in order to keep the stray capacitance at this node to a
minimum. Capacitance variations of less than 1 pF at the invert-
ing input will affect high speed performance.
Stripline design techniques should be used for long signal traces
(greater than approximately 1 inch). These should be designed
with a characteristic impedance of 50
or 75 and be properly
terminated at each end.
相關PDF資料 |
PDF描述 |
|---|---|
| DS4402N+T&R/C | IC DAC 2CH I2C ADJ 14-TDFN |
| VE-J1W-MW-S | CONVERTER MOD DC/DC 5.5V 100W |
| DS4422N+T&R | IC DAC 7BIT 2CH 5.5V 14-TDFN |
| VE-J1V-MW-S | CONVERTER MOD DC/DC 5.8V 100W |
| DS4422N+ | IC DAC 7BIT 2CH 5.5V 14-TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8073JRZ-REEL7 | 功能描述:IC VIDEO AMP TRIPLE 14-SOIC RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| AD8074ARU | 功能描述:IC TRPL VID BUFF 500MHZ 16-TSSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| AD8074ARU-REEL | 制造商:Analog Devices 功能描述:OP Amp Triple GP 制造商:Analog Devices 功能描述:OP Amp Triple GP ±5.5V 16-Pin TSSOP T/R 制造商:Rochester Electronics LLC 功能描述:TSSOP 400MHZ G=+1 TRPL VID BUF W/DISABLE - Tape and Reel |
| AD8074ARU-REEL7 | 制造商:Analog Devices 功能描述:OP Amp Triple GP |
| AD8074ARUZ | 功能描述:IC BUFFER TRPL VIDEO HS 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。