- 您現在的位置：買賣IC網 > PDF目錄5921 > AD8130AR (Analog Devices Inc)IC AMP DIFF LN LDIST 40MA 8SOIC PDF資料下載
參數資料
| 型號： | AD8130AR |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 32/41頁 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF LN LDIST 40MA 8SOIC |
| 設計資源： | High CMRR Circuit for Converting Wideband Complementary DAC Outputs to Single-Ended Without Precision Resistors (CN0142) |
| 標準包裝： | 98 |
| 放大器類型： | 差分 |
| 電路數： | 1 |
| 轉換速率： | 1100 V/µs |
| -3db帶寬： | 290MHz |
| 電流 - 輸入偏壓： | 500nA |
| 電壓 - 輸入偏移： | 400µV |
| 電流 - 電源： | 13mA |
| 電流 - 輸出 / 通道： | 40mA |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 25.2 V，±2.25 V ~ 12.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
AD8129/AD8130
Rev. C | Page 37 of 40
Another problem can occur with the AD8129 operating
at a supply voltage of greater than or equal to ±12 V. The
architecture causes the supply current to increase as the input
differential voltage increases. If the AD8129 differential inputs
are overdriven too far, excessive current can flow into the device
and potentially cause permanent damage.
A practical means to prevent this from occurring is to clamp the
inputs differentially with a pair of antiparallel Schottky diodes
(see Figure 146). These diodes have a lower forward voltage of
approximately 0.4 V. If the differential voltage across the inputs
is restricted to these conditions, no excess current is drawn by
the AD8129 under these operating conditions.
If the supply voltage is restricted to less than ±11 V, the internal
clamping circuit limits the differential voltage and excessive
supply current is not drawn. The external clamp circuit is not
needed.
VIN
AGILENT
HSMS 2822
1
2
3
VOUT
–V
+V
–VS
PD
+VS
+
VIN
AD8129
6
2
5
4
8
1
3
7
0.1
μF
10
μF
0.1
μF10μF
02464-147
Figure 146. Schottky Diodes Across the Inputs
Limits the Input Differential Voltage
In both circuits, the input series resistors function to limit the
current through the diodes when they are forward biased. As a
practical matter, these resistors must be matched so that the
CMRR is preserved at high frequencies. These resistors have
minimal effect on the CMRR at low frequency.
POWER DISSIPATION
The AD8129/AD8130 can operate with supply voltages from
+5 V to ±12 V. The major reason for such a wide supply range is
to provide a wide input common-mode range for systems that
can require this. This would be encountered when significant
common-mode noise couples into the input path. For applications
that do not require a wide dynamic range for the input or output, it
is recommended to operate with lower supply voltages.
The AD8129/AD8130 is also available in a very small 8-lead
MSOP package. This package has higher thermal impedance
than larger packages and operates at a higher temperature with
the same amount of power dissipation. Certain operating
conditions that are within the specifications range of the parts can
cause excess power dissipation. Caution should be exercised.
The power dissipation is a function of several operating
conditions, including the supply voltage, the input differential
voltage, the output load, and the signal frequency.
A basic starting point is to calculate the quiescent power
dissipation with no signal and no differential input voltage.
This is just the product of the total supply voltage and the
quiescent operating current. The maximum operating supply
voltage is 26.4 V, and the quiescent current is 13 mA. This
causes a quiescent power dissipation of 343 mW. For the
MSOP package, the θJA specification is 142°C/W. Therefore,
the quiescent power causes about a 49°C rise above ambient
in the MSOP package.
The current consumption is also a function of the differential
input voltage (see Figure 113 and Figure 114). This current
should be added onto the quiescent current and then multiplied
by the total supply voltage to calculate the power.
The AD8129/AD8130 can directly drive loads of as low as
100 Ω, such as a terminated 50 Ω cable. The worst-case power
dissipation in the output stage occurs when the output is at
midsupply. As an example, for a 12 V supply with the output
driving a 250 Ω load to ground, the maximum power dissipation
in the output occurs when the output voltage is 6 V. The load
current is 6 V/250 Ω = 24 mA. This same current flows through
the output across a 6 V drop from VS. It dissipates 144 mW. For
the 8-lead MSOP package, this causes a temperature rise of
20°C above ambient. Although this is a worst-case number, it is
apparent that this can be a considerable additional amount of
power dissipation.
Several changes can be made to alleviate this. One is to use the
standard 8-lead SOIC package. This lowers the thermal impedance
to 121°C/W, which is a 15% improvement. Another is to use a
lower supply voltage unless absolutely necessary.
Finally, do not use the AD8129/AD8130 when it is operating on
high supply voltages to directly drive a heavy load. It is best to
use a second op amp after the output stage. Some of the gain
can be shifted to this stage so that the signal swing at the output
of the AD8129/AD8130 is not too large.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1993IUD-4#PBF | IC DIFF AMP/ADC DRVR 16-QFN |
| ADA4817-1ARDZ-R7 | IC OPAMP VF 410MHZ LN 40MA 8SOIC |
| OP284FSZ-REEL7 | IC OPAMP GP R-R 4.25MHZ LN 8SOIC |
| AD8295ACPZ-WP | IC AMP INST 1MHZ TRPL LN 16LFCSP |
| GTCS25-900M-R02 | GAS TUBE 5MM 90V 20% 2.5KA SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8130AR | 制造商:Analog Devices 功能描述:SEMICONDUCTOR ((NW)) |
| AD8130AR-EB | 制造商:Analog Devices 功能描述:LEADED EVALUATION BOARD - Boxed Product (Development Kits) |
| AD8130AR-EBZ | 功能描述:BOARD EVAL FOR AD8130AR RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AD8130ARM | 功能描述:IC AMP DIFF LN LDIST 40MA 8MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:100 系列:- 放大器類型:通用 電路數:1 輸出類型:- 轉換速率:0.2 V/µs 增益帶寬積:- -3db帶寬:- 電流 - 輸入偏壓:100pA 電壓 - 輸入偏移:30µV 電流 - 電源:380µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):±2 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:管件 |
| AD8130ARM-EBZ | 功能描述:BOARD EVAL FOR AD8130ARM RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
發布緊急采購，3分鐘左右您將得到回復。