+VS
參數資料
型號： AD8226BRZ-RL
廠商： Analog Devices Inc
文件頁數： 11/28頁
文件大小： 0K
描述： IC INSTR AMP RRO +/-18 8SOIC
標準包裝： 2,500
放大器類型： 儀表
電路數： 1
輸出類型： 滿擺幅
轉換速率： 0.6 V/µs
-3db帶寬： 1.5MHz
電流 - 輸入偏壓： 20nA
電壓 - 輸入偏移： 100µV
電流 - 電源： 350µA
電流 - 輸出 / 通道： 13mA
電壓 - 電源，單路/雙路(±)： 2.2 V ~ 36 V，±1.35 V ~ 18 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 8-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 8-SO
包裝： 帶卷 (TR)
Data Sheet
AD8226
Rev. C | Page 19 of 28
THEORY OF OPERATION
A3
R2
24.7k
R1
24.7k
A1
A2
Q2
Q1
–IN
+IN
+VS
–VS
R3
50k
R4
50k
R5
50k
RB
+VS
–VS
VOUT
REF
07
03
6-
0
03
NODE 1
NODE 2
RG
VBIAS
+VS
–VS
+VS
–VS
NODE 4
NODE 3
R6
50k
DIFFERENCE
AMPLIFIER STAGE
GAIN STAGE
ESD AND
OVERVOLTAGE
PROTECTION
ESD AND
OVERVOLTAGE
PROTECTION
–VS
Figure 58. Simplified Schematic
ARCHITECTURE
The AD8226 is based on the classic 3-op-amp topology. This
topology has two stages: a preamplifier to provide differential
amplification, followed by a difference amplifier to remove the
common-mode voltage. Figure 58 shows a simplified schematic
of the AD8226.
The first stage works as follows: in order to maintain a constant
voltage across the bias resistor RB, A1 must keep Node 3 a con-
stant diode drop above the positive input voltage. Similarly, A2
keeps Node 4 at a constant diode drop above the negative input
voltage. Therefore, a replica of the differential input voltage is
placed across the gain-setting resistor, RG. The current that
flows across this resistance must also flow through the R1
and R2 resistors, creating a gained differential signal between
the A2 and A1 outputs. Note that, in addition to a gained
differential signal, the original common-mode signal, shifted
a diode drop up, is also still present.
The second stage is a difference amplifier, composed of A3 and
four 50 kΩ resistors. The purpose of this stage is to remove the
common-mode signal from the amplified differential signal.
The transfer function of the AD8226 is
VOUT = G(VIN+ VIN) + VREF
where:
G
R
G
kΩ
49.4
1
GAIN SELECTION
Placing a resistor across the RG terminals sets the gain of the
AD8226, which can be calculated by referring to Table 7 or by
using the following gain equation:
1
kΩ
49.4
G
R
G
Table 7. Gains Achieved Using 1% Resistors
1% Standard Table Value of RG (Ω)
Calculated Gain
49.9 k
1.990
12.4 k
4.984
5.49 k
9.998
2.61 k
19.93
1.00 k
50.40
499
100.0
249
199.4
100
495.0
49.9
991.0
The AD8226 defaults to G = 1 when no gain resistor is used.
The tolerance and gain drift of the RG resistor should be added
to the AD8226 specifications to determine the total gain accu-
racy of the system. When the gain resistor is not used, gain
error and gain drift are minimal.
If a gain of 5 is required and minimal gain drift is important,
consider using the AD8227. The AD8227 has a default gain of 5
that is set with internal resistors. Because all resistors are internal,
the gain drift is extremely low (<5 ppm/°C maximum).
相關PDF資料
PDF描述
0034.5143 FUSE 7A 250V 6.3X32 FAST GLASS
AD8226BRMZ-RL IC INSTR AMP RRO +/-18 8MSOP
0459844432 CONN RCPT R/A 4PWR 20SGL 2.36MM
0034.5140 FUSE 6A 250V 6.3X32 FAST GLASS
LTC6104HMS8#TRPBF IC AMP CURRENT SENSE 8-MSOP
相關代理商/技術參數
參數描述
AD8226CRMZ 制造商:AD 制造商全稱:Analog Devices 功能描述:Wide Supply Range, Rail-to-Rail Output Instrumentation Amplifier
AD8226CRMZ-R7 制造商:AD 制造商全稱:Analog Devices 功能描述:Wide Supply Range, Rail-to-Rail Output Instrumentation Amplifier
AD8226CRMZ-RL 制造商:AD 制造商全稱:Analog Devices 功能描述:Wide Supply Range, Rail-to-Rail Output Instrumentation Amplifier
AD8226CRZ 制造商:AD 制造商全稱:Analog Devices 功能描述:Wide Supply Range, Rail-to-Rail Output Instrumentation Amplifier
AD8226CRZ-R7 制造商:AD 制造商全稱:Analog Devices 功能描述:Wide Supply Range, Rail-to-Rail Output Instrumentation Amplifier
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*