- 您現在的位置：買賣IC網 > PDF目錄5922 > AD823AR-REEL (Analog Devices Inc)IC OPAMP JFET R-R DUAL LN 8SOIC PDF資料下載
參數資料
| 型號： | AD823AR-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/20頁 |
| 文件大小： | 0K |
| 描述： | IC OPAMP JFET R-R DUAL LN 8SOIC |
| 標準包裝： | 2,500 |
| 放大器類型： | J-FET |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 25 V/µs |
| -3db帶寬： | 16MHz |
| 電流 - 輸入偏壓： | 5pA |
| 電壓 - 輸入偏移： | 700µV |
| 電流 - 電源： | 7mA |
| 電流 - 輸出 / 通道： | 17mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 36 V，±1.5 V ~ 18 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 帶卷 (TR) |
Data Sheet
AD823
Rev. E | Page 15 of 20
APPLICATION NOTES
INPUT CHARACTERISTICS
In the AD823, N-Channel JFETs are used to provide a low offset,
low noise, high impedance input stage. Minimum input common-
mode voltage extends from 0.2 V below VS to 1 V < +VS. Driving
the input voltage closer to the positive rail causes a loss of amplifier
bandwidth and increased common-mode voltage error.
The AD823 does not exhibit phase reversal for input voltages up
to and including +VS. Figure 38 shows the response of an AD823
voltage follower to a 0 V to 5 V (+VS) square wave input. The
input and output are superimposed. The output polarity tracks
the input polarity up to +VS, with no phase reversal. The reduced
bandwidth above a 4 V input causes the rounding of the output
wave form. For input voltages greater than +VS, a resistor in
series with the AD823’s noninverting input prevents phase
reversal, at the expense of greater input voltage noise. This is
illustrated in Figure 39.
GND
100
0%
1V
2s
1V
90
00901-
038
10
Figure 38. AD823 Input Response: RP = 0, VIN = 0 to +VS
+VS
GND
5V
VIN
RP
VOUT
AD823
1V
10 s
1V
00901-
039
90
100
10
0%
Figure 39. AD823 Input Response:
VIN = 0 to +VS + 200 mV, VOUT = 0 to +VS, RP = 49.9 k
Because the input stage uses N-Channel JFETs, input current
during normal operation is negative; the current flows out from
the input terminals. If the input voltage is driven more positive
than +VS 0.4 V, the input current reverses direction as internal
device junctions become forward biased. This is illustrated in
A current limiting resistor should be used in series with the
input of the AD823 if there is a possibility of the input voltage
exceeding the positive supply by more than 300 mV, or if an
input voltage is applied to the AD823 when ±VS = 0. The
amplifier becomes damaged if left in that condition for more
than 10 seconds. A 1 k resistor allows the amplifier to
withstand up to 10 V of continuous overvoltage and increases
the input voltage noise by a negligible amount.
Input voltages less than VS are a completely different story.
The amplifier can safely withstand input voltages 20 V below
VS as long as the total voltage from the positive supply to the
input terminal is less than 36 V. In addition, the input stage
typically maintains picoamp level input currents across that
input voltage range.
The AD823 is designed for 16 nV/√Hz wideband input voltage
noise and maintains low noise performance to low frequencies
(see Figure 16). This noise performance, along with the AD823’s
low input current and current noise, means that the AD823
contributes negligible noise for applications with source
resistances greater than 10 k and signal bandwidths greater
than 1 kHz.
OUTPUT CHARACTERISTICS
The AD823’s unique bipolar rail-to-rail output stage swings
within 25 mV of the supplies with no external resistive load.
The AD823’s approximate output saturation resistance is 25
sourcing and sinking. This can be used to estimate the output
saturation voltage when driving heavier current loads. For
instance, when driving 5 mA, the saturation voltage to the rails
is approximately 125 mV.
If the AD823’s output is driven hard against the output
saturation voltage, it recovers within 250 ns of the input
returning to the amplifier’s linear operating region.
A/D Driver
The rail-to-rail output of the AD823 makes it useful as an A/D
driver in a single-supply system. Because it is a dual op amp, it
can be used to drive both the analog input of the A/D as well as
its reference input. The high impedance FET input of the
AD823 is well suited for minimal loading of high output
impedance devices.
相關PDF資料 |
PDF描述 |
|---|---|
| TMM-130-01-G-S-SM | CONN HEADER 30POS SNGL 2MM SMD |
| TSW-136-14-G-D | CONN HEADER 72POS .100" DL GOLD |
| GTCA28-601M-R10 | GAS TUBE 8MM 600V 20% 10KA |
| TMM-138-01-T-D-SM | CONN HEADER 76POS DUAL 2MM SMD |
| 961107-6404-AR | CONN HEADER VERT SGL 7POS GOLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD823AR-REEL7 | 功能描述:IC OPAMP JFET R-R DUAL LN 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:73 系列:Over-The-Top® 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.07 V/µs 增益帶寬積:200kHz -3db帶寬:- 電流 - 輸入偏壓:1nA 電壓 - 輸入偏移:285µV 電流 - 電源:50µA 電流 - 輸出 / 通道:25mA 電壓 - 電源，單路/雙路(±):2 V ~ 44 V，±1 V ~ 22 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WFDFN 裸露焊盤 供應商設備封裝:16-DFN-EP（5x3） 包裝:管件 |
| AD823ARZ | 功能描述:IC OPAMP JFET R-R DUAL LN 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD823ARZ | 制造商:Analog Devices 功能描述:Operational Amplifier (Op-Amp) IC |
| AD823ARZ-R7 | 功能描述:IC OPAMP JFET R-R DUAL LN 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
| AD823ARZ-RL | 功能描述:IC OPAMP JFET R-R DUAL LN 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
發布緊急采購，3分鐘左右您將得到回復。