- 您現在的位置：買賣IC網 > PDF目錄6027 > AD824ARZ-14 (Analog Devices Inc)IC OPAMP JFET R-R 2MHZ LP 14SOIC PDF資料下載
參數資料
| 型號： | AD824ARZ-14 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP JFET R-R 2MHZ LP 14SOIC |
| 標準包裝： | 56 |
| 放大器類型： | J-FET |
| 電路數： | 4 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 2 V/µs |
| 增益帶寬積： | 2MHz |
| -3db帶寬： | 2MHz |
| 電流 - 輸入偏壓： | 4pA |
| 電壓 - 輸入偏移： | 500µV |
| 電流 - 電源： | 560µA |
| 電流 - 輸出 / 通道： | 12mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 30 V，±1.5 V ~ 15 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 772 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
REV. C
AD824
–14–
A design consideration in sample-and-hold circuits is voltage
droop at the output caused by op amp bias and switch leakage
currents. By choosing a JFET op amp and a low leakage CMOS
switch, this design minimizes droop rate error to better than
0.1
mV/ms in this circuit. Higher values of CH will yield a lower
droop rate. For best performance, CH and C2 should be poly-
styrene, polypropylene or Teflon capacitors. These types of
capacitors exhibit low leakage and low dielectric absorption. Addi-
tionally, 1% metal film resistors were used throughout the design.
In the sample mode, SW1 and SW4 are closed, and the output
is VOUT = –VIN. The purpose of SW4, which operates in parallel
with SW1, is to reduce the pedestal, or hold step, error by
injecting the same amount of charge into the noninverting input
of A3 that SW1 injects into the inverting input of A3. This
creates a common-mode voltage across the inputs of A3 and is
then rejected by the CMR of A3; otherwise, the charge injection
from SW1 would create a differential voltage step error that
would appear at VOUT. The pedestal error for this circuit is
less than 2 mV over the entire 0 V to 3.3 V/5 V signal range.
Another method of reducing pedestal error is to reduce the pulse
amplitude applied to the control pins. In order to control the
ADG513, only 2.4 V are required for the “ON” state and
0.8V for the “OFF” state. If possible, use an input control
signal whose amplitude ranges from 0.8 V to 2.4 V instead of a
full range 0 V to 3.3 V/5 V for minimum pedestal error.
Other circuit features include an acquisition time of less than
3
ms to 1%; reducing CH and C2 will speed up the acquisition
time further, but an increased pedestal error will result. Settling
time is less than 300 ns to 1%, and the sample-mode signal BW
is 80 kHz.
The ADG513 was chosen for its ability to work with 3 V/5 V
supplies and for having normallyopen and normallyclosed preci-
sion CMOS switches on a dielectrically isolated process. SW2 is
not required in this circuit; however, it was used in parallel with
SW3 to provide a lower RON analog switch.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8228BRZ | IC AMP INST PREC LDRIFT LN 8SOIC |
| OP284EPZ | IC OPAMP GP R-R 4.25MHZ LN 8DIP |
| AD9632ARZ | IC OPAMP VF ULDIST 70MA 8SOIC |
| AD713JRZ-16-REEL7 | IC OPAMP BIFET QUAD PREC 16SOIC |
| LT1014ISW#PBF | IC OPAMP PRECISION QUAD 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD824ARZ-14-3V | 功能描述:IC OPAMP JFET R-R 2MHZ LP 14SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
| AD824ARZ-14-3V-RL | 功能描述:IC OPAMP JFET R-R 2MHZ LP 14SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| AD824ARZ-14-REEL | 功能描述:IC OPAMP JFET R-R 2MHZ LP 14SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| AD824ARZ-14-REEL7 | 功能描述:IC OPAMP JFET R-R 2MHZ LP 14SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:150 系列:- 放大器類型:音頻 電路數:2 輸出類型:- 轉換速率:5 V/µs 增益帶寬積:12MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:500µV 電流 - 電源:6mA 電流 - 輸出 / 通道:50mA 電壓 - 電源，單路/雙路(±):4 V ~ 32 V，±2 V ~ 16 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| AD824BN | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single Supply, Rail-to-Rail Low Power, FET-Input Op Amp |
發布緊急采購，3分鐘左右您將得到回復。