參數資料
型號： AD8260ACPZ-RL
廠商： Analog Devices Inc
文件頁數： 15/32頁
文件大?。?/td> 0K
描述： IC AMP VGA DIFF LN 310MA 32LFCSP
標準包裝： 5,000
放大器類型： 可變?cè)鲆?br>
電路數： 1
輸出類型： 差分
轉換速率： 730 V/µs
-3db帶寬： 195MHz
電流 - 輸入偏壓： 200nA
電流 - 電源： 28.3mA
電流 - 輸出 / 通道： 310mA
電壓 - 電源，單路/雙路(±)： 3.3 V ~ 10 V，±3.3 V ~ 5 V
工作溫度： -40°C ~ 105°C
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤，CSP
供應商設備封裝： 32-LFCSP-VQ
包裝： 帶卷 (TR)
配用： AD8260-EVALZ-ND - BOARD EVAL FOR AD8260
AD8260
Rev. A | Page 22 of 32
PRECAUTIONS TO BE OBSERVED DURING HALF-
DUPLEX OPERATION
During receive, when the high current driver-amplifier is
disabled, its gain setting resistors provide a signal path from
input to output. To prevent inadvertent DAC signals from being
transmitted while receiving via the preamplifier and DGA, the
DAC in Figure 64 must have no output signal.
During transmit, the preamplifier and VGA should be disabled
through any of the nongain-setting codes (see Table 4).
VMID BUFFER
The VMID buffer is a dc bias source that generates the voltage
on Pin 1 and Pin 19, VMDO. Node VMDO cannot accommodate
large dynamic currents and requires excellent ac decoupling to
ground. A high quality 0.1μF capacitor located as close as
possible to Pin 1 and Pin 19 (see Figure 64) is normally sufficient
to decouple the high values of current from Node VMDO.
When operating with dual power supplies, the buffer is disabled
by connecting Pin VMDI, Pin VOCM, and Pin VMDO to ground.
Because the logic decoder in the DGA (GNSx inputs) requires
3.3 V of headroom, the positive supply rails must be 3.3 V or
greater whether single-ended or dual. If a dual supply is used,
the negative rails are the same magnitude (opposite polarity)
as the positive, that is, 3.3 V when VPOS, VPSB, and VPSR
are +3.3 V.
PREAMPLIFIER
The AD8260 includes an uncommitted current feedback op
amp to buffer the resistive attenuator of the DGA. External
resistors are used to adjust the gain. The preamplifier is
characterized with a noninverting gain of 6 dB (2×) and both
gain resistor values of 100 . The preamplifier gain can be
increased using different gain ratios of RFB1 and RFB2, trading off
bandwidth and offset voltage. The sum of the values of RFB1 and
RFB2 should be ≥200 to maintain low distortion. RFB2 should
be ≥100 because it and an internal compensation capacitor
determine the 3 dB bandwidth of the amplifier. Smaller
resistor values may compromise preamplifier stability.
Because the AD8260 is internally dc-coupled, larger preamplifier
gains increase its offset voltage. The circuit contains an internal
bias resistor and some offset compensation; however, if a lower
value of offset voltage is required, it can be compensated by
connecting a resistor between the FDBK pin and the supply
voltage. If the offset is negative, the resistor value connects to
the negative supply; otherwise, it connects to the positive supply.
For larger gains, the overall noise is reduced if a low value of
RFB1 is selected. For values of RFB1 = 20 and RFB2 = 301 , the
preamplifier gain is 16× (24.1 dB) and the input-referred noise
is about 1.5 nV/√Hz. For this value of gain, the overall gain range
increases by 18 dB so that the absolute gain range is 12 dB to 42 dB.
PREAMPLIFIER NOISE
The total input-referred voltage and current noise of the positive
input of the preamplifier is about 2.4 nV/√Hz and 5 pA/√Hz,
respectively. The DGA output referred noise is about 25 nV/√Hz
at low gains and 39 nV/√Hz at the highest gain. The 25 nV/√Hz
divided by the DGA fixed gain of 8× results in 3.12 nV/√Hz
referred to the DGA input. Note that this value includes the
noise of the DGA gain setting resistors as well. If this voltage is
divided by the preamplifier gain of 2×, the DGA noise referred
all the way to the preamplifier input is about 1.56 nV/√Hz. From
this, it can be determined that the preamplifier, including the
100 gain setting resistors, contributes about 1.8 nV/√Hz. The
two 100 resistors each contribute 1.29 nV/√Hz at the output
of the preamplifier and 0.9 nV/√Hz referred to the input. With
the gain resistor noise subtracted, the preamplifier noise alone
is about 1.6 nV/√Hz.
Equation 1 shows the calculation that determines the output-
referred noise at maximum gain (24 dB or 16×).
(
)
2
,
2
,
2
1
2
,
2
,
2
,
2
,
)
(
)
(
)
(
)
(
)
(
VGA
n
VGA
RFB2
n
VGA
FB
RFB1
n
S
PrA
n
t
PrA
n
t
RS
n
out
n
A
e
A
e
A
R
e
R
i
A
e
A
e
×
+
×
+
×
+
×
+
×
+
×
=
(1)
where:
At is the total gain from preamplifier input to the VGA output.
en,RS is the noise of the source resistance.
en,PrA is the input-referred voltage noise of the preamplifier.
in,PrA is the current noise of the preamplifier at the PRAI pin.
RS is the source resistance.
AVGA is the VGA gain.
en,RFB1 is the voltage noise of RFB1.
en,RFB2 is the voltage noise of RFB2.
en,VGA is the input-referred voltage noise of DGA (low gain output-referred noise divided by a fixed gain of 8×).
相關PDF資料
PDF描述
170M3471 FUSE 500A 690V 1BKN/50 AR UC
1.5KE24CAHE3/54 TVS BIDIR 1.5KW 24V 5% 1.5KE
1.5KE22CAHE3/54 TVS BIDIRECT 1.5KW 22V 5% 1.5KE
1.5KE180CAHE3/54 TVS BIDIRECT 1.5KW 180V 5% 1.5KE
BK/GMA-V-3-R FUSE 3A 250V FAST GLASS AXL 5X20
相關代理商/技術參數
參數描述
AD8260ACPZ-WP 功能描述:IC AMP VGA DIFF LN 310MA 32LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR)
AD8260-EVALZ 功能描述:BOARD EVAL FOR AD8260 RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
AD8264 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad, 235 MHz, DC-Coupled VGA and Differential Output Amplifier
AD8264ACPZ 功能描述:IC AMP VGA DIFF QUAD LN 40LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT
AD8264ACPZ-R7 功能描述:IC AMP VGA DIFF QUAD LN 40LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*