- 您現在的位置：買賣IC網 > PDF目錄16923 > AD8337-EVALZ-INV (Analog Devices Inc)BOARD EVALUATION FOR AD8337 INS PDF資料下載
參數資料
| 型號： | AD8337-EVALZ-INV |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD8337 INS |
| 標準包裝： | 1 |
| 系列： | X-AMP® |
| 每 IC 通道數： | 1 - 單 |
| 放大器類型： | 電壓反饋 |
| 輸出類型： | 單端 |
| 轉換速率： | 625 V/µs |
| -3db帶寬： | 280MHz |
| 工作溫度： | -40°C ~ 85°C |
| 電流供應（主 IC）： | 18.5mA |
| 電壓 - 電源，單路/雙路(±)： | ±2.5 V ~ 5 V |
| 板類型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | AD8337 |
| 相關產品： | AD8337BCPZ-REEL7-ND - IC AMP VGA LOW NOISE 8-LFCSP AD8337BCPZ-REEL-ND - IC AMP VGA LOW NOISE 8-LFCSP AD8337BCPZ-WP-ND - IC AMP VGA DC-COUPLED GP 8-LFCSP AD8337BCPZ-R2DKR-ND - IC AMP VGA LOW NOISE 8-LFCSP AD8337BCPZ-R2CT-ND - IC AMP VGA LOW NOISE 8-LFCSP AD8337BCPZ-R2TR-ND - IC AMP VGA LOW NOISE 8-LFCSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD8337
Rev. C | Page 19 of
32
The gain scaling factor (gain slope) is designed for 20 dB/V. This
relatively low slope ensures that noise on the GAIN input is not
unduly amplified. Because a VGA functions as a multiplier, it is
important that the GAIN input does not inadvertently modulate
the output signal with unwanted noise. Because of its high input
impedance, a simple low-pass filter can be added to the GAIN
input to filter unwanted noise.
OUTPUT STAGE
The output stage is a Class AB, voltage-feedback, complementary
emitter-follower with a fixed gain of 18 dB, similar to the pream-
plifier in speed and bandwidth. Because of the ac-beta roll-off
of the output devices and the inherent reduction in feedback
beyond the 3 dB bandwidth, the impedance looking into the
output pin of the preamp and output stages appears to be inductive
(increasing impedance with increasing frequency). The high
speed output amplifier used in the AD8337 can drive large
currents, but its stability is susceptible to capacitive loading.
A small series resistor mitigates the effects of capacitive loading
(see the Applications Information section).
ATTENUATOR
The input resistance of the VGA attenuator is nominally 265 Ω.
For example, if the default preamplifier feedback network RFB1 +
RFB2 is 200 Ω, the effective preamplifier load is approximately
114 Ω. The attenuator is composed of eight 3.01 dB sections for
a total attenuation range of 24.08 dB. Following the attenuator
is a fixed gain amplifier with 8× (18.06 dB) gain. Because of this
relatively low gain, the output offset is kept well below 20 mV
over temperature; the offset is largest at maximum gain when
the preamplifier offset is amplified. The VCOM pin defines the
common-mode reference for the output, as shown in Figure 65.
SINGLE-SUPPLY OPERATION AND AC COUPLING
If the AD8337 is to be operated from a single 5 V supply, the
bias supply for VCOM must be a very low impedance 2.5 V
reference, especially if dc coupling is used. If the device is dc-
coupled, the VCOM source must be able to handle the preamplifier
and VGA dynamic load currents in addition to the bias currents.
When ac coupling the preamplifier input, a bias network and
bypass capacitor must be connected to the opposite polarity
input pin. The bias generator for the VCOM pin must provide
the dynamic current to the preamplifier feedback network and
the VGA attenuator. For many single 5 V applications, a refer-
ence, such as the ADR391, and a good op amp provide an
adequate VCOM source if a 2.5 V supply is unavailable.
NOISE
The total input-referred voltage and current noise of the positive
input of the preamplifier are about 2.2 nV/√Hz and 4.8 pA/√Hz.
The VGA output-referred noise is about 21 nV/√Hz at low gains.
This result is divided by the VGA fixed gain amplifier gain of 8×
and results in a voltage noise density of 2.6 nV/√Hz referred to
the VGA input. This value includes the noise of the VGA gain
setting resistors as well. If this voltage is again divided by the
preamp gain of 2, the VGA noise referred all the way to the
preamp input is about 1.3 nV/√Hz. From this, it is determined
that the preamplifier, including the 100 Ω gain setting resistors,
contributes about 1.8 nV/√Hz. The two 100 Ω resistors contribute
1.29 nV/√Hz each at the output of the preamp. With the gain
resistor noise subtracted, the preamplifier noise is approximately
1.55 nV/√Hz.
Equation 2 shows the calculation that determines the output-
referred noise at maximum gain (24 dB or 16×).
where:
At is the total gain from preamp input to VGA output.
RS is the source resistance.
enPrA is the input-referred voltage noise of the preamp.
inPrA is the current noise of the preamp at the INPP pin.
en
is the voltage noise of RFB1.
en
is the voltage noise of RFB2.
en VGA is the input-referred voltage noise of the VGA (low gain,
output-referred noise divided by a fixed gain of 8×).
1
FB
R
2
FB
R
Assuming RS = 0 Ω, RFB1 = RFB2 = 100 Ω, At = 16×, and AVGA =
8×, the noise simplifies to
en out =
Hz
nV
35
8)
(1.9
8)
2(1.29
16)
(1.75
2
=
×
+
×
+
×
(1)
Dividing the result by 16 gives the total input-referred noise with
a short-circuited input as 2.2 nV/√Hz. When the preamplifier is
used in the inverting configuration with the same RFB1 and RFB2=
100 Ω as previously noted, en out does not change. However,
because the gain dropped by 6 dB, the input-referred noise
increases by a factor of 2 to about 4.4 nV/√Hz. The reason for this
increase is that the noise gain to the output of the noise generators
stays the same, yet the preamp in the inverting configuration has a
gain of 1 compared to the +2 in the noninverting configuration;
this increases the input-referred noise by 2.
2
)
VGA
A
n
(e
2
)
VGA
A
n
(e
2
)
VGA
A
FB1
R
FB2
R
n
(e
2
)
S
R
n
(i
2
)
t
A
n
(e
2
t
A
S
R
n
e
n
e
VGA
R
PrA
out
FB2
FB1
×
+
×
+
×
+
×
+
×
+
×
=
)
(
(2)
相關PDF資料 |
PDF描述 |
|---|---|
| EBM30DCTS | CONN EDGECARD 60POS DIP .156 SLD |
| MIC2566-0YM | IC PCMCIA/CARDBUS SGL 14-SOP |
| AD8251-EVALZ | BOARD EVALUATION FOR AD8251 PGA |
| ISL21009DFB841Z-TK | IC VREF SERIES PREC 4.096V 8SOIC |
| AD8330-EVALZ | BOARD EVAL FOR AD8330 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8337-EVALZ-SS | 功能描述:BOARD EVALUATION FOR AD8337 SS RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:X-AMP® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AD8338 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, 18 MHz Variable Gain Amplifier |
| AD8338ACPZ-R7 | 功能描述:特殊用途放大器 Ultra Low Pwr 18MHz SGL CH VGA RoHS:否 制造商:Analog Devices 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:5 V 電源電流:133 mA 最大功率耗散:900 mW 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝:Reel |
| AD8338ACPZ-RL | 制造商:Analog Devices 功能描述:AMPLIFIER - SPECIAL PURPOSE |
| AD8338-EVALZ | 功能描述:AD8338 1 - Single Channels per IC Variable Gain Amplifier Evaluation Board 制造商:analog devices inc. 系列:- 零件狀態:有效 每 IC 通道數:1 - 單 放大器類型:可變增益 輸出類型:差分 壓擺率:50 V/μs -3db 帶寬:18MHz 電流 - 輸出/通道:- 工作溫度:-40°C ~ 85°C 電流 - 電源（主 IC）:- 電壓 - 電源，單/雙（±）:3.5 V ~ 5 V 板類型:完全填充 所含物品:板 使用的 IC/零件:AD8338 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。