- 您現在的位置：買賣IC網 > PDF目錄5885 > AD8554ARZ-REEL (Analog Devices Inc)IC OPAMP CHOPPER R-R QUAD 14SOIC PDF資料下載
參數資料
| 型號： | AD8554ARZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 14/24頁 |
| 文件大小： | 0K |
| 描述： | IC OPAMP CHOPPER R-R QUAD 14SOIC |
| 標準包裝： | 2,500 |
| 放大器類型： | 斷路器（零漂移） |
| 電路數： | 4 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 0.4 V/µs |
| 增益帶寬積： | 1.5MHz |
| 電流 - 輸入偏壓： | 10pA |
| 電壓 - 輸入偏移： | 1000µV |
| 電流 - 電源： | 850µA |
| 電流 - 輸出 / 通道： | 30mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 帶卷 (TR) |
Data Sheet
AD8551/AD8552/AD8554
Rev. E | Page 21 of 24
A HIGH ACCURACY THERMOCOUPLE AMPLIFIER
Figure 68 shows a K-type thermocouple amplifier configuration
with cold junction compensation. Even from a 5 V supply, the
AD8551 can provide enough accuracy to achieve a resolution of
better than 0.02°C from 0°C to 500°C. D1 is used as a tempera-
ture measuring device to correct the cold junction error from
the thermocouple and should be placed as close as possible to
the two terminating junctions. With the thermocouple measuring
tip immersed in a 0°C ice bath, R6 should be adjusted until the
output is at 0 V.
Using the values shown in Figure 68, the output voltage tracks
temperature at 10 mV/°C. For a wider range of temperature
measurement, R9 can be decreased to 62 kΩ. This creates a
5 mV/°C change at the output, allowing measurements of up
to 1000°C.
3
2
7
4
5V
+
REF02EZ
12V
2
6
4
D1
1N4148
5.000V
1
–
+
AD8551
0.1F
10F
K-TYPE
THERMOCOUPLE
40.7V/°C
0V TO 5.00V
(0°C TO 500°C)
R4
5.62k
R6
200
R3
53.6
R2
2.74k
R1
10.7k
R5
40.2k
R8
124k
R7
453
01101-
068
Figure 68. A Precision K-Type Thermocouple Amplifier with
Cold Junction Compensation
PRECISION CURRENT METER
Because of its low input bias current and superb offset voltage at
single supply voltages, the AD855x is an excellent amplifier for
precision current monitoring. Its rail-to-rail input allows the
amplifier to be used as either a high-side or low-side current
monitor. Using both amplifiers in the AD8552 provides a simple
method to monitor both current supply and return paths for
load or fault detection.
Figure 69 shows a high-side current monitor configuration. In
this configuration, the input common-mode voltage of the
amplifier is at or near the positive supply voltage. The rail-to-
rail input of the amplifier provides a precise measurement even
with the input common-mode voltage at the supply voltage. The
CMOS input structure does not draw any input bias current,
ensuring a minimum of measurement error.
The 0.1 Ω resistor creates a voltage drop to the noninverting
input of the AD855x. The output of the amplifier is corrected
until this voltage appears at the inverting input. This creates a
current through R1, which in turn flows through R2. The
monitor output is given by
L
1
SENSE
2
I
R
Output
Monitor
×
×
=
(23)
Using the components shown in Figure 69, the monitor output
transfer function is 2.5 V/A.
Figure 70 shows the low-side monitor equivalent. In this circuit,
the input common-mode voltage to the AD8552 is at or near
ground. Again, a 0.1 Ω resistor provides a voltage drop propor-
tional to the return current. The output voltage is given as
( )
×
+
=
L
SENSE
OUT
I
R
V
1
2
(24)
For the component values shown in Figure 70, the output
transfer function decreases from V+ at 2.5 V/A.
8
1
4
3
3V
V+
G
S
D
2
3V
1/2
AD8552
MONITOR
OUTPUT
M1
Si9433
R1
100
R2
2.49k
RSENSE
0.1
IL
0.1F
01101-
069
Figure 69. A High-Side Load Current Monitor
V+
1/2 AD8552
V+
Q1
RETURN TO
GROUND
VOUT
R2
2.49k
R1
100
RSENSE
0.1
01101-
070
Figure 70. A Low-Side Load Current Monitor
PRECISION VOLTAGE COMPARATOR
The AD855x can be operated open-loop and used as a precision
comparator. The AD855x has less than 50 μV of offset voltage
when run in this configuration. The slight increase of offset
voltage stems from the fact that the autocorrection architecture
operates with lowest offset in a closed-loop configuration, that
is, one with negative feedback. With 50 mV of overdrive, the
device has a propagation delay of 15 μs on the rising edge and
8 μs on the falling edge. Ensure the maximum differential
voltage of the device is not exceeded. For more information,
refer to the Input Overvoltage Protection section.
相關PDF資料 |
PDF描述 |
|---|---|
| 929715-03-13-I | CONN HEADER .100 DUAL STR 26POS |
| 929665-02-26-I | CONN HEADER .100 DUAL STR 52POS |
| SL1021B400RF | GAS TUBE 400V HVY 10KA 3PIN RADL |
| SL1021B350RF | GAS TUBE 350V HVY 10KA 3PIN RADL |
| TMM-129-01-S-S-SM | CONN HEADER 29POS SNGL 2MM SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8554ARZ-REEL7 | 功能描述:IC OPAMP CHOPPER R-R QUAD 14SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:73 系列:Over-The-Top® 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.07 V/µs 增益帶寬積:200kHz -3db帶寬:- 電流 - 輸入偏壓:1nA 電壓 - 輸入偏移:285µV 電流 - 電源:50µA 電流 - 輸出 / 通道:25mA 電壓 - 電源，單路/雙路(±):2 V ~ 44 V，±1 V ~ 22 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WFDFN 裸露焊盤 供應商設備封裝:16-DFN-EP（5x3） 包裝:管件 |
| AD8555 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Zero-Drift, Digitally Programmable Sensor Signal Amplifier |
| AD8555_09 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Zero-Drift, Digitally Programmable Sensor Signal Amplifier |
| AD85551 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10 MHz, 20 V/レs, G = 1, 10, 100, 1000 i CMOS㈢ Programmable Gain Instrumentation Amplifier |
| AD8555ACP | 制造商:Analog Devices 功能描述:SP AMP CURRENT SENSE AMP SGL R-R I/O 5.5V 16LFCSP EP - Bulk |
發布緊急采購，3分鐘左右您將得到回復。