- 您現在的位置：買賣IC網 > PDF目錄6069 > AD8556ACPZ-REEL7 (Analog Devices Inc)IC AMP CHOPPER 2MHZ 10MA 16LFCSP PDF資料下載
參數資料
| 型號： | AD8556ACPZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/28頁 |
| 文件大小： | 0K |
| 描述： | IC AMP CHOPPER 2MHZ 10MA 16LFCSP |
| 標準包裝： | 1 |
| 系列： | DigiTrim® |
| 放大器類型： | 斷路器（零漂移） |
| 電路數： | 1 |
| 轉換速率： | 1.2 V/µs |
| 增益帶寬積： | 2MHz |
| 電流 - 輸入偏壓： | 49nA |
| 電壓 - 輸入偏移： | 2µV |
| 電流 - 電源： | 2mA |
| 電流 - 輸出 / 通道： | 10mA |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 140°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-VQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 16-LFCSP-VQ |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 771 (CN2011-ZH PDF) |
| 其它名稱： | AD8556ACPZ-REEL7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD8556
Rev. A | Page 23 of 28
Important:
Once a programming attempt is made for any
fuse, there should be no further attempt to blow that fuse.
If a fuse does not program to the expected state, discard
the unit. The expected incidence rate of attempted but
unblown fuses is very small when following the proper
programming procedure and conditions.
3.
Set VSS to 0 V and VDD to 5.25 V (±0.25 V). Power
supplies should be capable of supplying 250 mA at the
required voltage and properly bypassed as described
in the Programming Mode section. Use program mode to
permanently enter the desired codes for the first stage gain,
second stage gain, and output offset. Blow the parity bit
fuse if necessary (see Parity Error Detection section). Blow
the master fuse to allow the AD8556 to read data from the
fuses and to prevent further programming.
4.
Set VDD and VSS to the desired values in the application.
Use read mode with low sense current followed by high
sense current to verify programmed codes.
5.
Measure gain and offset to verify correct functionality.
Determining Optimal Gain and Offset Codes
First, determine the desired gain:
1.
Determine the desired gain, GA (using the measurements
obtained from the simulation).
2.
that (4.00 × 1.04) < (GA/G2) < (6.4/1.04). This ensures the
first and last codes for the first stage gain are not used,
thereby allowing enough first stage gain codes within each
second stage gain range to adjust for the 3% accuracy.
Next, set the second stage gain:
1.
Use the simulation mode to set the second stage gain to G2.
2.
Set the output offset to allow the AD8556 gain to be
measured, for example, use Code 128 to set it to
midsupply.
3.
Use Table 5 or Equation 1 to set the first stage gain code
CG1, so the first stage gain is nominally GA/G2.
4.
Measure the resulting gain, GB. G
B
should be within
3% of GA.
5.
Calculate the first stage gain error (in relative terms)
EG1 = GB/G
B
A
1.
6.
Calculate the error (in the number of the first stage gain
codes) CEG1 = EG1/0.00370.
7.
Set the first stage gain code to CG1 CEG1.
8.
Measure the gain, GC. GC should be closer to GA than to GB.
B
9.
Calculate the error (in relative terms) EG2 = GC/GA 1.
10. Calculate the error (in the number of the first stage gain
codes) CEG2 = EG2/0.00370.
11. Set the first stage gain code to CG1 CEG1 CEG2. The
resulting gain should be within one code of GA.
Finally, determine the desired output offset:
1.
Determine the desired output offset OA (using the
measurements obtained from the simulation).
2.
Use Equation 2 to set the output offset code CO1 such that
the output offset is nominally OA.
3.
Measure the output offset, OB. O
B
should be within
3% of OA.
4.
Calculate the error (in relative terms) EO1 = OB/O
B
A
1.
5.
Calculate the error (in the number of the output offset
codes) CEO1 = EO1/0.00392.
6.
Set the output offset code to CO1 CEO1.
7.
Measure the output offset, OC. OC should be closer to OA
than to OB.
B
8.
Calculate the error (in relative terms) EO2 = OC/OA 1.
9.
Calculate the error (in the number of the output offset
codes) CEO2 = EO2/0.00392.
10. Set the output offset code to CO1 CEO1 CEO2. The
resulting offset should be within one code of OA.
相關PDF資料 |
PDF描述 |
|---|---|
| GB0504AFV1-8 | BLOWER 5VDC 40 X 40 X 9.3MM |
| RMCF2512FT2R00 | RES TF 2 OHM 1% 1W 2512 |
| 151210-2420-RB-WC | CONN 10POS 2MM HEADER DL STR SMD |
| 0316005.NRT1 | FUSE PICO 5A 125V FAST CCC AXL |
| GB1205PKV1-8AY | BLOWER 12VDC 50 X 50 X 20MM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8556ARZ | 功能描述:IC AMP CHOPPER 2MHZ 10MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:DigiTrim® 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD8556ARZ-REEL | 功能描述:IC AMP CHOPPER 2MHZ 10MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:DigiTrim® 標準包裝:73 系列:Over-The-Top® 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.07 V/µs 增益帶寬積:200kHz -3db帶寬:- 電流 - 輸入偏壓:1nA 電壓 - 輸入偏移:285µV 電流 - 電源:50µA 電流 - 輸出 / 通道:25mA 電壓 - 電源，單路/雙路(±):2 V ~ 44 V，±1 V ~ 22 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WFDFN 裸露焊盤 供應商設備封裝:16-DFN-EP（5x3） 包裝:管件 |
| AD8556ARZ-REEL7 | 功能描述:IC AMP CHOPPER 2MHZ 10MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:DigiTrim® 標準包裝:73 系列:Over-The-Top® 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.07 V/µs 增益帶寬積:200kHz -3db帶寬:- 電流 - 輸入偏壓:1nA 電壓 - 輸入偏移:285µV 電流 - 電源:50µA 電流 - 輸出 / 通道:25mA 電壓 - 電源，單路/雙路(±):2 V ~ 44 V，±1 V ~ 22 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WFDFN 裸露焊盤 供應商設備封裝:16-DFN-EP（5x3） 包裝:管件 |
| AD8556CP-EBZ | 功能描述:AD8556 DigiTrim? Series 1 - Single Channels per IC Chopper (Zero-Drift) Amplifier Evaluation Board 制造商:analog devices inc. 系列:DigiTrim? 零件狀態:有效 每 IC 通道數:1 - 單 放大器類型:斷路器（零漂移） 輸出類型:單端 壓擺率:1.2 V/μs -3db 帶寬:- 電流 - 輸出/通道:10mA 工作溫度:-40°C ~ 140°C 電流 - 電源（主 IC）:2mA 電壓 - 電源，單/雙（±）:4.5 V ~ 5.5 V 板類型:完全填充 所含物品:板 使用的 IC/零件:AD8556 標準包裝:1 |
| AD8556-EVALZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) |
發布緊急采購，3分鐘左右您將得到回復。