參數資料
型號： AD8601ARTZ-REEL7
廠商： Analog Devices Inc
文件頁數： 7/24頁
文件大?。?/td> 0K
描述： IC OPAMP GP CMOS 8.4MHZ SOT23-5
產品培訓模塊： Top Five Problems in Photodiode Opamp Circuits
設計資源： Fully Isolated Input Module Based on AD7793, ADuM5401, and a High Performance In-Amp (CN0067)
標準包裝： 1
系列： DigiTrim®
放大器類型： 通用
電路數： 1
輸出類型： 滿擺幅
轉換速率： 6 V/µs
增益帶寬積： 8.4MHz
電流 - 輸入偏壓： 0.2pA
電壓 - 輸入偏移： 80µV
電流 - 電源： 750µA
電流 - 輸出 / 通道： 50mA
電壓 - 電源，單路/雙路(±)： 2.7 V ~ 5.5 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： SC-74A，SOT-753
供應商設備封裝： SOT-23-5
包裝： 標準包裝
產品目錄頁面： 773 (CN2011-ZH PDF)
其它名稱： AD8601ARTZREEL7DKR
AD8601/AD8602/AD8604
Rev. G | Page 15 of 24
THEORY OF OPERATION
The AD8601/AD8602/AD8604 family of amplifiers are rail-to-rail
input and output, precision CMOS amplifiers that operate from
2.7 V to 5.0 V of the power supply voltage. These amplifiers use
Analog Devices, Inc., DigiTrim technology to achieve a higher
degree of precision than available from most CMOS amplifiers.
DigiTrim technology is a method of trimming the offset voltage
of the amplifier after it has been assembled. The advantage in post-
package trimming lies in the fact that it corrects any offset voltages
due to the mechanical stresses of assembly. This technology is
scalable and used with every package option, including the 5-lead
SOT-23, providing lower offset voltages than previously achieved in
these small packages.
The DigiTrim process is completed at the factory and does not
add additional pins to the amplifier. All AD860x amplifiers are
available in standard op amp pinouts, making DigiTrim completely
transparent to the user. The AD860x can be used in any precision
op amp application.
The input stage of the amplifier is a true rail-to-rail architecture,
allowing the input common-mode voltage range of the op amp
to extend to both positive and negative supply rails. The voltage
swing of the output stage is also rail-to-rail and is achieved by
using an NMOS and PMOS transistor pair connected in a
common-source configuration. The maximum output voltage
swing is proportional to the output current, and larger currents
limit how close the output voltage can get to the supply rail,
which is a characteristic of all rail-to-rail output amplifiers.
With 1 mA of output current, the output voltage can reach
within 20 mV of the positive rail and within 15 mV of the
negative rail. At light loads of >100 kΩ, the output swings
within ~1 mV of the supplies.
The open-loop gain of the AD860x is 80 dB, typical, with a load
of 2 kΩ. Because of the rail-to-rail output configuration, the gain
of the output stage and the open-loop gain of the amplifier are
dependent on the load resistance. Open-loop gain decreases with
smaller load resistances. Again, this is a characteristic inherent
to all rail-to-rail output amplifiers.
RAIL-TO-RAIL INPUT STAGE
The input common-mode voltage range of the AD860x extends
to both the positive and negative supply voltages. This maximizes
the usable voltage range of the amplifier, an important feature
for single-supply and low voltage applications. This rail-to-rail
input range is achieved by using two input differential pairs, one
NMOS and one PMOS, placed in parallel. The NMOS pair is
active at the upper end of the common-mode voltage range, and
the PMOS pair is active at the lower end.
The NMOS and PMOS input stages are separately trimmed using
DigiTrim to minimize the offset voltage in both differential pairs.
Both NMOS and PMOS input differential pairs are active in a
500 mV transition region, when the input common-mode voltage
is between approximately 1.5 V and 1 V below the positive supply
voltage. The input offset voltage shifts slightly in this transition
region, as shown in Figure 9 and Figure 10 .The common-mode
rejection ratio is also slightly lower when the input common-
mode voltage is within this transition band. Compared to the
Burr-Brown OPA2340UR rail-to-rail input amplifier, shown in
Figure 54, the AD860x, shown in Figure 55, exhibits lower
offset voltage shift across the entire input common-mode
range, including the transition region.
0.7
0.4
0.1
–0.2
–0.5
–0.8
–1.1
–1.4
01
2
3
45
VCM (V)
V
OS
(m
V)
01
52
5-
05
4
Figure 54. Burr-Brown OPA2340UR Input Offset Voltage vs.
Common-Mode Voltage, 24 SOIC Units @ 25°C
0.7
0.4
0.1
–0.2
–0.5
–0.8
–1.1
–1.4
01
2
3
45
VCM (V)
V
OS
(m
V)
01
52
5-
05
5
Figure 55. AD8602AR Input Offset Voltage vs. Common-Mode Voltage,
300 SOIC Units @ 25°C
相關PDF資料
PDF描述
69192-420 BERGSTIK II DR STRAIGHT RET
929400-01-10-RK CONN HEADER .100 SNGL STR 10POS
AD8692ARMZ-REEL IC OPAMP GP R-R CMOS 10MHZ 8MSOP
26630301RP2 CONN HDR 2MM MALE 1ROW STR 3POS
GBC02SABN-M30 CONN HEADER 2POS .100 SINGLE SMD
相關代理商/技術參數
參數描述
AD8601DRT 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision CMOS Single Supply Rail-to-Rail Input/Output Wideband Operational Amplifiers
AD8601DRT-R2 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision CMOS Single-Supply Rail-to-Rail Input/Output Wideband Operational Amplifiers
AD8601DRT-REEL 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision CMOS Single-Supply Rail-to-Rail Input/Output Wideband Operational Amplifiers
AD8601DRT-REEL7 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision CMOS Single-Supply Rail-to-Rail Input/Output Wideband Operational Amplifiers
AD8601WARTZ-R7 功能描述:IC AMP GP R-R I/O SGL SOT23-5 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:DigiTrim® 標準包裝:160 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:10 V/µs 增益帶寬積:9MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:250µV 電流 - 電源:730µA 電流 - 輸出 / 通道:28mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*