- 您現在的位置：買賣IC網 > PDF目錄5448 > AD8655ARZ-REEL7 (Analog Devices Inc)IC OPAMP GP R-R CMOS 28MHZ 8SOIC PDF資料下載
參數資料
| 型號： | AD8655ARZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/20頁 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP R-R CMOS 28MHZ 8SOIC |
| 設計資源： | Single Supply Low Noise LED Current Source Driver Using a Current Output DAC in the Reverse Mode (CN0139) |
| 標準包裝： | 1,000 |
| 系列： | DigiTrim® |
| 放大器類型： | 通用 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 11 V/µs |
| 增益帶寬積： | 28MHz |
| 電流 - 輸入偏壓： | 1pA |
| 電壓 - 輸入偏移： | 50µV |
| 電流 - 電源： | 3.7mA |
| 電流 - 輸出 / 通道： | 220mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 帶卷 (TR) |
AD8655/AD8656
Data Sheet
Rev. E | Page 18 of 20
LAYOUT, GROUNDING, AND BYPASSING CONSIDERATIONS
POWER SUPPLY BYPASSING
Power supply pins can act as inputs for noise, so care must be
taken to apply a noise-free, stable dc voltage. The purpose of
bypass capacitors is to create low impedances from the supply
to ground at all frequencies, thereby shunting or filtering most
of the noise. Bypassing schemes are designed to minimize the
supply impedance at all frequencies with a parallel combination
of capacitors with values of 0.1 F and 4.7 F. Chip capacitors
of 0.1 F (X7R or NPO) are critical and should be as close as
possible to the amplifier package. The 4.7 F tantalum capacitor
is less critical for high frequency bypassing, and, in most cases,
only one is needed per board at the supply inputs.
GROUNDING
A ground plane layer is important for densely packed PC
boards to minimize parasitic inductances. This minimizes
voltage drops with changes in current. However, an under-
standing of where the current flows in a circuit is critical to
implementing effective high speed circuit design. The length
of the current path is directly proportional to the magnitude
of parasitic inductances, and, therefore, the high frequency
impedance of the path. Large changes in currents in an
inductive ground return create unwanted voltage noise.
The length of the high frequency bypass capacitor leads is
critical, and, therefore, surface-mount capacitors are recom-
mended. A parasitic inductance in the bypass ground trace
works against the low impedance created by the bypass
capacitor. Because load currents flow from the supplies, the
ground for the load impedance should be at the same physical
location as the bypass capacitor grounds. For larger value
capacitors intended to be effective at lower frequencies, the
current return path distance is less critical.
LEAKAGE CURRENTS
Poor PC board layout, contaminants, and the board insulator
material can create leakage currents that are much larger than
differential between the inputs and nearby traces creates leakage
currents through the PC board insulator, for example, 1 V/100
G = 10 pA. Similarly, any contaminants on the board can
create significant leakage (skin oils are a common problem).
To significantly reduce leakage, put a guard ring (shield) around
the inputs and input leads that are driven to the same voltage
potential as the inputs. This ensures there is no voltage potential
between the inputs and the surrounding area to create any
leakage currents. To be effective, the guard ring must be driven
by a relatively low impedance source and should completely
surround the input leads on all sides, above and below, by using
a multilayer board.
The charge absorption of the insulator material itself can also
cause leakage currents. Minimizing the amount of material
between the input leads and the guard ring helps to reduce the
absorption. Also, using low absorption materials, such as
Teflon or ceramic, may be necessary in some instances.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8602ARZ-REEL7 | IC OPAMP GP CMOS 8.4MHZ 8SOIC |
| S506-125-R | FUSE .125A 250V T-LAG GLASS IEC |
| RL0816S-R10-F | RES 0.10 OHM 1/5W 1% 0603 |
| OP177GS-REEL | IC OPAMP GP PREC LN 8SOIC |
| ADA4851-2YRMZ-RL7 | IC OPAMP VF R-R DUAL LP 8MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8655WARMZ-RL | 功能描述:General Purpose Amplifier 1 Circuit Rail-to-Rail 8-MSOP 制造商:analog devices inc. 系列:DigiTrim? 包裝:帶卷（TR） 零件狀態:有效 放大器類型:通用 電路數:1 輸出類型:滿擺幅 壓擺率:11 V/μs 增益帶寬積:28MHz -3db 帶寬:- 電流 - 輸入偏置:1pA 電壓 - 輸入失調:50μV 電流 - 電源:3.7mA 電流 - 輸出/通道:220mA 電壓 - 電源，單/雙（±）:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商器件封裝:8-MSOP 標準包裝:3,000 |
| AD8656 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Noise, Precision CMOS Amplifier |
| AD8656ARMZ | 功能描述:IC OPAMP GP R-R CMOS 28MHZ 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:DigiTrim® 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| AD8656ARMZ | 制造商:Analog Devices 功能描述:IC OP-AMP 28MHZ 11V/ MSOP-8 |
| AD8656ARMZ-R2 | 制造商:Analog Devices 功能描述:OP Amp Dual Volt Fdbk R-R I/O 5.5V 8-Pin MSOP T/R 制造商:Analog Devices 功能描述:Operational Amplifier (Op-Amp) IC |
發布緊急采購，3分鐘左右您將得到回復。