- 您現在的位置：買賣IC網 > PDF目錄17059 > AD9116-DPG2-EBZ (Analog Devices Inc)IC DAC DUAL 12BIT LO PWR 40LFCSP PDF資料下載
參數資料
| 型號： | AD9116-DPG2-EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 36/52頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC DUAL 12BIT LO PWR 40LFCSP |
| 標準包裝： | 1 |
| 系列： | TxDAC® |
| DAC 的數量： | 2 |
| 位數： | 12 |
| 采樣率（每秒）： | 125M |
| 數據接口： | 串行 |
| DAC 型： | 電流 |
| 工作溫度： | -40°C ~ 85°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | AD9116 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
Data Sheet
AD9114/AD9115/AD9116/AD9117
Rev. C | Page 41 of 52
3
2
1
0
D-FF
4
D-FF
OR
DCLKIO-INT
CLKIN-INT
DB[n:0]
(INPUT)
TO DAC CORE
IOUT
DE
L
AY
1
DELAY2
DE
L
AY
1
R
E
T
IM
E
R-
CL
K
IE
OE
DCLKIO
(INPUT/OUTPUT)
CLKIN
(INPUT)
NOTES
D-FFs:
0: RISING OR FALLING EDGE
TRIGGERED FOR I OR Q DATA.
1, 2, 3, 4: RISING EDGE TRIGGERED.
RETIMER-CLK
07
46
6-
05
6
NOTES:
1. DB[n:0], WHERE n IS 7 FOR THE AD9114, 9 FOR THE AD9115, 11 FOR THE AD9116, AND 13 FOR THE AD9117.
Figure 94. Simplified Diagram of AD9114/AD9115/AD9116/AD9117 Timing
DIGITAL DATA LATCHING AND RETIMER SECTION
The AD9114/AD9115/AD9116/AD9117 have two clock inputs,
DCLKIO and CLKIN. The CLKIN is the analog clock whose
jitter affects DAC performance, and the DCLKIO is a digital clock
from an FPGA that needs to have a fixed relationship with the
input data to ensure that the data is sampled correctly by the
flip-flops on the pads.
Figure 94 is a simplified diagram of the entire data capture
system in the AD9114/AD9115/AD9116/AD9117. The double
data rate input data (DB[n:0], where n is 7 for the AD9114, is 9
for the AD9115, is 11 for the AD9116, and 13 for the AD9117) is
latched at the pads/pins either on the rising edge or the falling edge
of the DCLKIO-INT clock, as determined by IRISING, Bit 4 of
SPI Address 0x02. Bit 5 of SPI Address 0x02, IFIRST, determines
which channel data is latched first (that is, I or Q). The captured
data is then retimed to the internal clock (CLKIN-INT) in the
retimer block before being sent to the final analog DAC core
(D-FF 4), which controls the current steering output switches. All
delay blocks depicted in Figure 94 are non-inverting, and any wires
without an explicit delay block can be assumed to have no delay.
Only one channel is shown in Figure 94 with the data pads
(DB[n:0], where n is 7 for the AD9114, is 9 for the AD9115, is
11 for the AD9116, and 13 for the AD9117) serving as double
data rate pads for both channels.
The default PINMD and SPI settings are IE = high (closed) and
OE = low (open). These settings are enabled when RESET/PINMD
(Pin 35) is held high. In this mode, the user has to supply both
DCLKIO and CLKIN. In PINMD, it is also recommended that the
DCLKIO and the CLKIN be in phase for proper functioning of
the DAC, which can easily be ensured by tying the pins together
on the PCB. If the user can access the SPI, setting Bit 2 of SPI
Address 0x02, DCI_EN, to logic low causes the CLKIN to be
used as the DCLKIO also.
Setting Bit 1 or Bit 0 of SPI Address 0x02, DCOSGL or DCODBL,
to logic high allows the user to get a DCLKIO output from the
CLKIN input for use in the user’s PCB system.
It is strongly recommended that DCI_EN = DCOSGL = high,
or DCI_EN = DCODBL = high not be used, even though the
device may appear to function correctly. Similarly, DCOSGL
and DCODBL should not be set to logic high simultaneously.
Retimer
The AD9114/AD9115/AD9116/AD9117 have an internal data
retimer circuit that compares the CLKIN-INT and DCLKIO-INT
clocks and, depending on their phase relationship, selects a
retimer clock (RETIMER-CLK) to safely transfer data from the
DCLKIO used at the chip’s input interface to the CLKIN used to
clock the analog DAC cores (D-FF 4).
The retimer selects one of the three phases shown in Figure 95.
The retimer is controlled by the CLKMODE SPI bits as is
shown in Table 15.
1/2 PERIOD
1/4 PERIOD
1/2 PERIOD
DATA
CLOCK
RETIMER-CLKs
180°
90°
270°
07
46
6-
0
57
Figure 95. RETIMER-CLK Phases
Note that, in most cases, more than one retimer phase works
and, in such cases, the retimer arbitrarily picks one phase that
works. The retimer cannot pick the best or safest phase. If the
user has a working knowledge of the exact phase relationship
between DCLKIO and CLKIN (and thus DCLKIO-INT and
CLKIN-INT because the delay is approximately the same for
both clocks and equal to DELAY1), then the retimer can be
forced to this phase with CLKMODEN = 1, as described in
Table 15 and the following paragraphs.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B4X-EY | CONVERTER MOD DC/DC 5.2V 50W |
| AD9117-DPG2-EBZ | IC DAC DUAL 14BIT LO PWR 40LFCSP |
| AD9114-DPG2-EBZ | IC DAC DUAL 8BIT LO PWR 40LFCSP |
| AD9115-DPG2-EBZ | IC DAC DUAL 10BIT LO PWR 40LFCSP |
| 0210490184 | CABLE JUMPER 1.25MM .229M 12POS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9116-EBZ | 制造商:Analog Devices 功能描述:DUAL 12 BIT LOW POWER CONVERTER - Boxed Product (Development Kits) |
| AD9117 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual, 8-/10-/12-/14-Bit Low Power Digital-to-Analog Converters |
| AD9117BCPZ | 功能描述:IC DAC DUAL 14BIT LO PWR 40LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| AD9117BCPZN | 功能描述:數模轉換器- DAC Dual 14B Low Power D-A Converter RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| AD9117BCPZNRL7 | 功能描述:數模轉換器- DAC Dual Low Pwr 14-Bit RoHS:否 制造商:Analog Devices 轉換器數量:4 DAC 輸出端數量:4 轉換速率: 分辨率:12 bit 接口類型:Serial (I2C) 穩定時間: 最大工作溫度:+ 105 C 安裝風格: 封裝 / 箱體:TSSOP 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。