- 您現在的位置：買賣IC網 > PDF目錄10669 > AD9215BRUZ-105 (Analog Devices Inc)IC ADC 10BIT 105MSPS 3V 28-TSSOP PDF資料下載
參數資料
| 型號： | AD9215BRUZ-105 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 35/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 105MSPS 3V 28-TSSOP |
| 設計資源： | Very Low Jitter Encode (Sampling) Clocks for High Speed Analog-to-Digital Converters Using ADF4002 (CN0003) Interfacing the High Frequency AD8331 to AD9215 (CN0096) |
| 標準包裝： | 50 |
| 位數： | 10 |
| 采樣率（每秒）： | 105M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 120mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，單極；1 個差分，單極 |
| 產品目錄頁面： | 780 (CN2011-ZH PDF) |
| 配用： | AD9215BCP-80EBZ-ND - BOARD EVAL FOR AD9215BCP-80 AD9215BCP-65EBZ-ND - BOARD EVAL FOR AD9215BCP-65 AD9215BCP-105EBZ-ND - BOARD EVAL FOR AD9215BCP-105 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁
AD9215
Data Sheet
Rev. B | Page 8 of 36
EQUIVALENT CIRCUITS
02874-A-005
AVDD
MODE
Figure 5. Equivalent Analog Input Circuit
02874-A-006
AVDD
MODE
20k
Figure 6. Equivalent MODE Input Circuit
02874-A-007
D9–D0,
OR
DRVDD
Figure 7. Equivalent Digital Output Circuit
02874-A-008
2.6k
2.6k
AVDD
CLK
Figure 8. Equivalent Digital Input Circuit
DEFINITIONS OF SPECIFICATIONS
Aperture Delay
Aperture delay is a measure of the sample-and-hold amplifier
(SHA) performance and is measured from the rising edge of the
clock input to when the input signal is held for conversion.
Aperture Jitter
Aperture jitter is the variation in aperture delay for successive
samples and can be manifested as frequency-dependent noise
on the input to the ADC.
Clock Pulse Width and Duty Cycle
Pulse width high is the minimum amount of time that the clock
pulse should be left in the Logic 1 state to achieve rated perfor-
mance. Pulse width low is the minimum time the clock pulse
should be left in the low state. At a given clock rate, these speci-
fications define an acceptable clock duty cycle.
Differential Nonlinearity (DNL, No Missing Codes)
An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value. Guaranteed
no missing codes to 10-bit resolution indicate that all 1024
codes, respectively, must be present over all operating ranges.
Effective Number of Bits (ENOB)
For a sine wave, SINAD can be expressed in terms of the num-
ber of bits. Using the following formula, it is possible to obtain a
measure of performance expressed as N, the effective number of
bits
N = (SINAD – 1.76)/6.02
Thus, the effective number of bits for a device for sine wave
inputs at a given input frequency can be calculated directly
from its measured SINAD.
Gain Error
The first code transition should occur at an analog value 1/2
LSB above negative full scale. The last transition should occur at
an analog value 1 1/2 LSB below the positive full scale. Gain
error is the deviation of the actual difference between the first
and last code transitions and the ideal difference between the
first and last code transitions.
Integral Nonlinearity (INL)
INL refers to the deviation of each individual code from a line
drawn from “negative full scale” through “positive full scale.”
The point used as negative full scale occurs 1/2 LSB before the
first code transition. Positive full scale is defined as a level 1 1/2
LSB beyond the last code transition. The deviation is measured
from the middle of each particular code to the true straight line.
Maximum Conversion Rate
The clock rate at which parametric testing is performed.
Minimum Conversion Rate
The clock rate at which the SNR of the lowest analog signal
frequency drops by no more than 3 dB below the guaranteed
limit.
Offset Error
The major carry transition should occur for an analog value 1/2
LSB below VIN+ = VIN. Zero error is defined as the deviation
of the actual transition from that point.
Out-of-Range Recovery Time
Out-of-range recovery time is the time it takes for the ADC to
reacquire the analog input after a transient from 10% above
positive full scale to 10% above negative full scale, or from 10%
below negative full scale to 10% below positive full scale.
Output Propagation Delay
The delay between the clock logic threshold and the time when
all bits are within valid logic levels.
Power Supply Rejection
The specification shows the maximum change in full scale from
the value with the supply at the minimum limit to the value
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2442CG#PBF | IC ADC 24BIT 4CH 36-SSOP |
| LTC2418IGN#PBF | IC ADC 24BIT DIFF INPUT 28SSOP |
| AD7651ASTZ | IC ADC 16BIT 100KSPS 48-LQFP |
| VI-2WM-IX-B1 | CONVERTER MOD DC/DC 10V 75W |
| LTC1402CGN#PBF | IC ADC 12BIT 2.2MSPS SHDN 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9215BRUZ-105 | 制造商:Analog Devices 功能描述:AD CONVERTOR ((NW)) |
| AD9215BRUZ-105 | 制造商:Analog Devices 功能描述:10BIT ADC 105MSPS 9215 TSSOP28 |
| AD9215BRUZ-65 | 功能描述:IC ADC 10BIT 65MSPS 3V 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD9215BRUZ-65 | 制造商:Analog Devices 功能描述:10BIT ADC 65MSPS 9215 TSSOP28 |
| AD9215BRUZ-80 | 功能描述:IC ADC 10BIT 80MSPS 3V 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。