參數資料
型號: AD9233BCPZRL7-125
廠商: Analog Devices Inc
文件頁數: 17/44頁
文件大?。?/td> 0K
描述: IC ADC 12BIT 125MSPS 48-LFCSP
標準包裝: 750
位數: 12
采樣率(每秒): 125M
數據接口: 串行,SPI?
轉換器數目: 1
功率耗散(最大): 425mW
電壓電源: 單電源
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 48-VFQFN 裸露焊盤,CSP
供應商設備封裝: 48-LFCSP-VQ(7x7)
包裝: 帶卷 (TR)
輸入數目和類型: 2 個單端,單極;1 個差分,單極
配用: AD9233-125EBZ-ND - BOARD EVALUATION FOR AD9233
AD9233
Rev. A | Page 24 of 44
MEMORY MAP
READING THE MEMORY MAP TABLE
Each row in the memory map table has eight address locations.
The memory map is roughly divided into three sections: chip
configuration registers map (Address 0x00 to Address 0x02),
device index and transfer registers map (Address 0xFF), and
ADC functions map (Address 0x08 to Address 0x18).
The memory map register in Table 15 displays the register
address number in hexadecimal in the first column. The last
column displays the default value for each hexadecimal address.
The Bit 7 (MSB) column is the start of the default hexadecimal
value given. For example, Hexadecimal Address 0x14,
output_phase has a hexadecimal default value of 0x00. This
means Bit 3 = 0, Bit 2 = 0, Bit 1 = 1, and Bit 0 = 1 or 0011 in
binary. This setting is the default output clock or DCO phase
adjust option. The default value adjusts the DCO phase 90°
relative to the nominal DCO edge and 180° relative to the data
edge. For more information on this function, consult the
Open Locations
Locations marked as open are currently not supported for this
device. When required, these locations should be written with
0s. Writing to these locations is required only when part of an
address location is open (for example, Address 0x14). If the
entire address location is open (Address 0x13), then the address
location does not need to be written.
Default Values
Coming out of reset, critical registers are loaded with default
values. The default values for the registers are provided in Table 15.
Logic Levels
An explanation of two registers follows:
Bit is set is synonymous with bit is set to Logic 1 or writing
Logic 1 for the bit.
Clear a bit is synonymous with bit is set to Logic 0 or
writing Logic 0 for the bit.
SPI-Accessible Features
A list of features accessible via the SPI and a brief description of
what the user can do with these features follows. These features
are described in detail in the Interfacing to High Speed ADCs via
Modes:
Set either power-down or standby mode.
Clock:
Access the DCS via the SPI.
Offset:
Digitally adjust the converter offset.
Test I/O:
Set test modes to have known data on output bits.
Output Mode:
Setup outputs, vary the strength of the
output drivers.
Output Phase:
Set the output clock polarity.
VREF:
Set the reference voltage.
DON’T CARE
SDIO
SCLK
CSB
tS
tDH
tHI
tCLK
tLO
tDS
tH
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
D4
D3
D2
D1
D0
05492-
053
Figure 57. Serial Port Interface Timing Diagram
相關PDF資料
PDF描述
AD9235BRURL7-40 IC ADC 12BIT SGL 40MSPS 28TSSOP
AD9236BRUZRL7-80 IC ADC 12BIT 80MSPS 28TSSOP
AD9237BCPZ-20 IC ADC 12BIT SGL 20MSPS 32LFCSP
AD9238BSTRL-65 IC ADC 12BIT DUAL 65MSPS 64-LQFP
AD9239BCPZ-170 IC ADC 12BIT DUAL 170MSPS 72PIN
相關代理商/技術參數
參數描述
AD9233BCPZRL7-80 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit, 80 MSPS/105 MSPS/125 MSPS, 1.8 V Analog-to-Digital Converter
AD9234-1000EBZ 功能描述:AD9234 - 12 Bit 1G Samples per Second Analog to Digital Converter (ADC) Evaluation Board 制造商:analog devices inc. 系列:- 零件狀態:有效 A/D 轉換器數:2 位數:12 采樣率(每秒):1G 數據接口:JESD204B 輸入范圍:1.34 Vpp 不同條件下的功率(典型值):3W @ 1GSPS 使用的 IC/零件:AD9234 所含物品:板 標準包裝:1
AD9234BCPZ-1000 功能描述:IC ADC 12BIT 1GSPS 64LFCSP 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 位數:12 采樣率(每秒):1G 輸入數:2 輸入類型:差分 數據接口:JESD204B 配置:S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:1 架構:管線 參考類型:內部 電壓 - 電源,模擬:1.22 V ~ 1.28 V,2.44 V ~ 2.56 V 電壓 - 電源,數字:1.22 V ~ 1.28 V 特性:- 工作溫度:-40°C ~ 85°C 封裝/外殼:64-WFQFN 裸露焊盤 供應商器件封裝:64-LFCSP-WQ(9x9) 標準包裝:1
AD9234BCPZRL7-1000 功能描述:IC ADC 12BIT 1GSPS 64LFCSP 制造商:analog devices inc. 系列:- 包裝:帶卷(TR) 零件狀態:在售 位數:12 采樣率(每秒):1G 輸入數:2 輸入類型:差分 數據接口:JESD204B 配置:S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:1 架構:管線 參考類型:內部 電壓 - 電源,模擬:1.22 V ~ 1.28 V,2.44 V ~ 2.56 V 電壓 - 電源,數字:1.22 V ~ 1.28 V 特性:- 工作溫度:-40°C ~ 85°C 封裝/外殼:64-VFQFN 裸露焊盤,CSP 供應商器件封裝:64-LFCSP-VQ(9x9) 標準包裝:750
AD9234-EB 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed ADC USB FIFO Evaluation Kit