- 您現在的位置：買賣IC網 > PDF目錄373961 > AD9241AS (ANALOG DEVICES INC) RES., MF, 2K, 1%, 1/4W PDF資料下載
參數資料
| 型號： | AD9241AS |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | RES., MF, 2K, 1%, 1/4W |
| 中文描述： | 1-CH 14-BIT FLASH METHOD ADC, PARALLEL ACCESS, PQFP44 |
| 封裝： | METRIC, QFP-44 |
| 文件頁數： | 5/24頁 |
| 文件大?。?/td> | 495K |
| 代理商： | AD9241AS |
AD9241
REV. 0
–5–
overvoltage (50% greater than full-scale range), measured from
the time the overvoltage signal reenters the converter’s range.
TEMPERATURE DRIFT
The temperature drift for zero error and gain error specifies the
maximum change from the initial (+25
°
C) value to the value at
T
MIN
or T
MAX
.
POWER SUPPLY REJECTION
The specification shows the maximum change in full scale,
from the value with the supply at the minimum limit to the
value with the supply at its maximum limit.
APERTURE JITTER
Aperture jitter is the variation in aperture delay for successive
samples and is manifested as noise on the input to the A/D.
APERTURE DELAY
Aperture delay is a measure of the sample-and-hold amplifier
(SHA) performance and is measured from the rising edge of the
clock input to when the input signal is held for conversion.
SIGNAL-TO-NOISE AND DISTORTION (S/N+D, SINAD)
RATIO
S/N+D is the ratio of the rms value of the measured input sig-
nal to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc.
The value for S/N+D is expressed in decibels.
EFFECTIVE NUMBER OF BITS (ENOB)
For a sine wave, SINAD can be expressed in terms of the num-
ber of bits. Using the following formula,
N
= (
SINAD
– 1.76)/6.02
it is possible to get a measure of performance expressed as
N
,
the effective number of bits.
Thus, the effective number of bits for a device for sine wave
inputs at a given input frequency can be calculated directly
from its measured SINAD.
TOTAL HARMONIC DISTORTION (THD)
THD is the ratio of the rms sum of the first six harmonic
components to the rms value of the measured input signal; this
is expressed as a percentage or in decibels.
SIGNAL-TO-NOISE RATIO (SNR)
SNR is the ratio of the rms value of the measured input signal
to the rms sum of all other spectral components below the
Nyquist frequency, excluding the first six harmonics and dc.
The value for SNR is expressed in decibels.
SPURIOUS FREE DYNAMIC RANGE (SFDR)
SFDR is the difference in dB between the rms amplitude of the
input signal and the peak spurious signal.
TWO-TONE SFDR
The ratio of the rms value of either input tone to the rms value
of the peak spurious component. The peak spurious component
may or may not be an IMD product. It may be reported in dBc
(i.e., degrades as signal level is lowered) or in dBFS (always
related back to converter full scale).
PIN FUNCTION DESCRIPTIONS
Pin
Number
Name
Description
1
2, 29
3
4, 28
5
6
7
8–10
11
12–23
24
25
26, 27, 30
31
32
33
34, 35, 38
40, 43, 44
36
37
39
41
42
DVSS
AVSS
DVDD
AVDD
DRVSS
DRVDD
CLK
NC
BIT 14
BIT 13–BIT 2
BIT 1
OTR
NC
SENSE
VREF
REFCOM
NC
Digital Ground
Analog Ground
+5 V Digital Supply
+5 V Analog Supply
Digital Output Driver Ground
Digital Output Driver Supply
Clock Input Pin
No Connect
Least Significant Data Bit (LSB)
Data Output Bits
Most Significant Data Bit (MSB)
Out of Range
No Connect
Reference Select
Reference I/O
Reference Common
No Connect
CAPB
CAPT
CML
VINA
VINB
Noise Reduction Pin
Noise Reduction Pin
Common-Mode Level (Midsupply)
Analog Input Pin (+)
Analog Input Pin (–)
DEFINITIONS OF SPECIFICATION
INTEGRAL NONLINEARITY (INL)
INL refers to the deviation of each individual code from a line
drawn from “negative full scale” through “positive full scale.”
The point used as “negative full scale” occurs 1/2 LSB before
the first code transition. “Positive full scale” is defined as a level
1 1/2 LSB beyond the last code transition. The deviation is
measured from the middle of each particular code to the true
straight line.
DIFFERENTIAL NONLINEARITY (DNL, NO MISSING
CODES)
An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value. Guaranteed
no missing codes to 14-bit resolution indicates that all 16384
codes, respectively, must be present over all operating ranges.
ZERO ERROR
The major carry transition should occur for an analog value
1/2 LSB below VINA = VINB. Zero error is defined as the
deviation of the actual transition from that point.
GAIN ERROR
The first code transition should occur at an analog value
1/2 LSB above negative full scale. The last transition should
occur at an analog value 1 1/2 LSB below the nominal full
scale. Gain error is the deviation of the
actual
difference
between first and last code transitions, and the
ideal
differ-
ence between first and last code transitions.
OVERVOLTAGE RECOVERY TIME
Overvoltage recovery time is defined as that amount of time
required for the ADC to achieve a specified accuracy after an
相關PDF資料 |
PDF描述 |
|---|---|
| AD9241EB | Complete 14-Bit, 1.25 MSPS Monolithic A/D Converter |
| AD9243 | Complete 14-Bit, 3.0 MSPS Monolithic A/D Converter |
| AD9243AS | Complete 14-Bit, 3.0 MSPS Monolithic A/D Converter |
| AD9243EB | Complete 14-Bit, 3.0 MSPS Monolithic A/D Converter |
| AD9243* | 14-Bit Rail-to-Rail DACs with I2C Interface; Package: DFN; No of Pins: 10; Temperature Range: 0°C to +70°C |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9241ASRL | 制造商:Analog Devices 功能描述:ADC Single Pipelined 1.25Msps 14-bit Parallel 44-Pin MQFP T/R |
| AD9241ASZ | 功能描述:IC ADC 14BIT 1.25MSPS 44-MQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD9241ASZRL | 功能描述:IC ADC 14BIT SGL 1.25MSPS 44MQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD9241EB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 14-Bit, 1.25 MSPS Monolithic A/D Converter |
| AD9241-EB | 制造商:Analog Devices 功能描述:Evaluation Board For AD9241 制造商:Analog Devices 功能描述:EVAL BD FOR AD9241 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。