參數資料
型號: AD9518-1ABCPZ-RL7
廠商: Analog Devices Inc
文件頁數: 46/64頁
文件大小: 0K
描述: IC CLOCK GEN 6CH 2.5GHZ 48LFCSP
標準包裝: 750
類型: 時鐘發生器,扇出配送
PLL:
輸入: CMOS,LVDS,LVPECL
輸出: LVPECL
電路數: 1
比率 - 輸入:輸出: 1:6
差分 - 輸入:輸出: 是/是
頻率 - 最大: 2.65GHz
除法器/乘法器: 是/無
電源電壓: 3.135 V ~ 3.465 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 48-VFQFN 裸露焊盤,CSP
供應商設備封裝: 48-LFCSP-VQ(7x7)
包裝: 帶卷 (TR)
AD9518-1
Data Sheet
Rev. C | Page 50 of 64
Reg.
Addr.
(Hex)
Bits
Name
Description
[1:0]
Antibacklash pulse
width
1
0
Antibacklash Pulse Width (ns)
0
2.9 (default); this is the recommended setting, and it does not normally need to be changed.
0
1
1.3; this setting may be necessary if the PFD frequency > 50 MHz.
1
0
6.0.
1
2.9.
0x018
[6:5]
Lock detect counter
Required consecutive number of PFD cycles with edges inside lock detect window before the DLD indicates a locked
condition.
6
5
PFD Cycles to Determine Lock
0
5 (default).
0
1
16.
1
0
64.
1
255.
4
Digital lock detect
window
If the time difference of the rising edges at the inputs to the PFD is less than the lock detect window time, the digital
lock detect flag is set. The flag remains set until the time difference is greater than the loss-of-lock threshold.
0: high range (default).
1: low range.
3
Disable digital lock
detect
Digital lock detect operation.
0: normal lock detect operation (default).
1: disables lock detect.
[2:1]
VCO cal divider
VCO calibration divider. Divider used to generate the VCO calibration clock from the PLL reference clock.
2
1
VCO Calibration Clock Divider
0
2. This setting is fine for PFD frequencies < 12.5 MHz. The PFD frequency is fREF/R.
0
1
4. This setting is fine for PFD frequencies < 25 MHz.
1
0
8. This setting is fine for PFD frequencies < 50 MHz.
1
16 (default). This setting is fine for any PFD frequency but also results in the longest VCO calibration time.
0
VCO cal now
Bit used to initiate VCO calibration. This bit must be toggled from 0b to 1b in the active registers. To initiate calibration,
use the following three steps: first, ensure that the input reference signal is present; second, set to 0b (if not zero
already), followed by the update all registers bit (Register 0x232, Bit 0); and third, program to 1b, again followed by the
update all registers bit (Register 0x232, Bit 0). Clearing this bit discards the VCO calibration and usually results in the
PLL losing lock. The user must ensure that the holdover enable bits in Register 0x01D = 00b during VCO calibration.
0x019
[7:6]
R, A, B counters,
SYNC pin reset
7
6
Action
0
Does nothing on SYNC (default).
0
1
Asynchronous reset.
1
0
Synchronous reset.
1
Does nothing on SYNC.
[5:3]
R path delay
R path delay (default = 0x00); see Table 2.
[2:0]
N path delay
N path delay (default = 0x00); see Table 2.
相關PDF資料
PDF描述
MS3450L28-11SZ CONN RCPT 22POS WALL MNT W/SCKT
AD9518-0ABCPZ-RL7 IC CLOCK GEN 6CH 2.8GHZ 48LFCSP
MS3450L28-11SY CONN RCPT 22POS WALL MNT W/SCKT
V150A5H300B CONVERTER MOD DC/DC 5V 300W
MS3450L28-11SX CONN RCPT 22POS WALL MNT W/SCKT
相關代理商/技術參數
參數描述
AD9518-1A-PCBZ 制造商:AD 制造商全稱:Analog Devices 功能描述:6-Output Clock Generator with Integrated 2.5 GHz VCO
AD9518-1BCPZ 制造商:Analog Devices 功能描述:Clock Generator 48-Pin LFCSP EP Tray
AD9518-1BCPZ-REEL7 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述:
AD9518-2 制造商:AD 制造商全稱:Analog Devices 功能描述:6-Output Clock Generator with Integrated 2.2 GHz VCO
AD9518-2A/PCBZ 功能描述:BOARD EVALUATION FOR AD9518-2A RoHS:是 類別:編程器,開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信,線路接口單元(LIU) 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板,電源,線纜,CD 其它名稱:82EBV2081