- 您現在的位置：買賣IC網 > PDF目錄9472 > AD974AN (Analog Devices Inc)IC DAS 16BIT 4CH 200KSPS 28-DIP PDF資料下載
參數資料
| 型號： | AD974AN |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 19/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAS 16BIT 4CH 200KSPS 28-DIP |
| 標準包裝： | 13 |
| 類型： | 數據采集系統（DAS） |
| 分辨率（位）： | 16 b |
| 采樣率（每秒）： | 200k |
| 數據接口： | 串行 |
| 電壓電源： | 模擬和數字 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 28-DIP（0.600"，15.24mm） |
| 供應商設備封裝： | 28-PDIP |
| 包裝： | 管件 |
| 配用： | EVAL-AD974CB-ND - BOARD EVAL FOR AD974 |
REV. A
AD974
–8–
can be read after the conversion is complete. The external clock
can be either a continuous or discontinuous clock. A discontinu-
ous clock can be either normally low or normally high when
inactive. In the case of the discontinuous clock, the AD974 can be
configured to either generate or not generate a SYNC output
(with a continuous clock a SYNC output will always be produced).
Each of the methods will be described in the following sections
and are illustrated in Figures 4 through 9. It should be noted
that all timing diagrams assume that the receiving device is
latching data on the rising edge of the external clock. If the
falling edge of DATACLK is used then, in the case of a discon-
tinuous clock, one less clock pulse is required than shown in
Figures 4 through 7 to latch in a 16-bit word. Note that data is
valid on the falling edge of a clock pulse (for t13 greater than t18)
and the rising edge of the next clock pulse.
The AD974 provides error correction circuitry that can correct
for an improper bit decision made during the first half of the
conversion cycle. Normally the occurrence of an incorrect bit
decision during a conversion cycle is irreversible. This error
occurs as a result of noise during the time of the decision or due
to insufficient settling time. As the AD974 is performing a
conversion it is important that transitions not occur on digital
input/output pins or degradation of the conversion result could
occur. This is particularly important during the second half of
the conversion process. For this reason it is recommended that
when an external clock is being provided it be a discontinuous
clock that is not toggling during the time that
BUSY is low or,
more importantly, that it does not transition during the latter
half of
BUSY low.
EXTERNAL DISCONTINUOUS CLOCK DATA READ
AFTER CONVERSION WITH NO SYNC OUTPUT
GENERATED
Figure 4 illustrates the method by which data from conversion
“n” can be read after the conversion is complete using a discon-
tinuous external clock without the generation of a SYNC
output. After a conversion is complete, indicated by
BUSY
returning high, the result of that conversion can be read while
CS is Low and R/C is high. In this mode CS can be tied low.
The MSB will be valid on the first falling edge and the second
rising edge of DATACLK. The LSB will be valid on the 16th
falling edge and the 17th rising edge of DATACLK. A mini-
mum of 16 clock pulses are required for DATACLK if the
receiving device will be latching data on the falling edge of
DATACLK. A minimum of 17 clock pulses are required for
DATACLK if the receiving device will be latching data on the
rising edge of DATACLK.
The advantage of this method of reading data is that data is not
being clocked out during a conversion and therefore conversion
performance is not degraded.
When reading data after the conversion is complete, with the
highest frequency permitted for DATACLK (15.15 MHz), the
maximum possible throughput is approximately 195 kHz, and
not the rated 200 kHz.
EXT
DATACLK
R/
C
BUSY
SYNC
DATA
t12
0
12
3
14
15
16
t13
t14
t1
t2
t21
t18
BIT 15
(MSB)
BIT 14
BIT 13
BIT 1
BIT 0
(LSB)
Figure 4. Conversion and Read Timing Using an External Discontinuous Data Clock
(EXT/
INT Set to Logic High, CS Set to Logic Low)
相關PDF資料 |
PDF描述 |
|---|---|
| V28A12M200BG2 | CONVERTER MOD DC/DC 12V 200W |
| AD974AR | IC DAS 16BIT 4CH 200KSPS 28-SOIC |
| LTC6907IS6#TRMPBF | IC OSC SILICON 4MHZ TSOT23-6 |
| AD7874AR-REEL7 | IC DAS 12BIT 4CH 5V 28-SOIC |
| V28A12M200BF2 | CONVERTER MOD DC/DC 12V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD974ANZ | 功能描述:IC DAS 16BIT 4CH 200KSPS 28DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD974AR | 功能描述:IC DAS 16BIT 4CH 200KSPS 28-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD974ARS | 制造商:Analog Devices 功能描述:ADC Single 200ksps 16-bit Serial 28-Pin SSOP 制造商:Rochester Electronics LLC 功能描述:4-CHANNEL 16 BIT 200KSPS DATA ACQ SYSTEM - Bulk |
| AD974ARSZ | 功能描述:IC DAS 16BIT 4CH 200KSPS 28-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Data Converter Basics 標準包裝:1 系列:- 類型:電機控制 分辨率（位）:12 b 采樣率（每秒）:1M 數據接口:串行，并聯 電壓電源:單電源 電源電壓:2.7 V ~ 3.6 V，4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:100-TQFP 供應商設備封裝:100-TQFP（14x14） 包裝:剪切帶 (CT) 其它名稱:296-18373-1 |
| AD974ARZ | 功能描述:IC DAS 16BIT 4CH 200KSPS 28-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Data Converter Basics 標準包裝:1 系列:- 類型:電機控制 分辨率（位）:12 b 采樣率（每秒）:1M 數據接口:串行，并聯 電壓電源:單電源 電源電壓:2.7 V ~ 3.6 V，4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:100-TQFP 供應商設備封裝:100-TQFP（14x14） 包裝:剪切帶 (CT) 其它名稱:296-18373-1 |
發布緊急采購，3分鐘左右您將得到回復。