參數資料
型號: AD9838ACPZ-RL
廠商: Analog Devices Inc
文件頁數: 17/32頁
文件大?。?/td> 0K
描述: IC DDS 16MHZ LOW PWR 20LFCSP
產品培訓模塊: Direct Digital Synthesis Tutorial Series (1 of 7): Introduction
Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action
Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter
Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction
Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter
Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator
標準包裝: 5,000
分辨率(位): 10 b
主 fclk: 5MHz
電源電壓: 2.3 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 20-WFQFN 裸露焊盤,CSP
供應商設備封裝: 20-LFCSP-WQ(4x4)
包裝: 帶卷 (TR)
AD9838
Rev. A | Page 24 of 32
APPLICATIONS INFORMATION
The various output options available from the AD9838 make
the part suitable for a wide variety of applications, including
modulation applications. The AD9838 can be used to perform
simple modulation, such as frequency shift keying (FSK). More
complex modulation schemes, such as Gaussian minimum shift
keying (GMSK) and quadrature phase shift keying (QPSK), can
also be implemented using the AD9838.
In an FSK application, the two frequency registers of the AD9838
are loaded with different values. One frequency represents the
space frequency, and the other represents the mark frequency. The
digital data stream is fed to the FSELECT pin, causing the AD9838
to modulate the carrier frequency between the two values.
The AD9838 has two phase registers, enabling the part to per-
form phase shift keying (PSK). With PSK, the carrier frequency
is phase shifted, that is, the phase is altered by an amount that
is related to the bit stream input to the modulator.
The AD9838 is also suitable for signal generator applications.
Using the on-board comparator, the device can be used to gen-
erate a square wave.
With its low current consumption, the part is also suitable for
applications in which it can be used as a local oscillator.
GROUNDING AND LAYOUT
The printed circuit board that houses the AD9838 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. This facilitates the use
of ground planes that can be separated easily. A minimum etch
technique is generally best for ground planes because it provides
the best shielding. Digital and analog ground planes should be
joined in one place only. If the AD9838 is the only device that
requires an AGND to DGND connection, the ground planes
should be connected at the AGND and DGND pins of the
AD9838. If the AD9838 is in a system where multiple devices
require AGND to DGND connections, the connection should
be made at one point only, a star ground point that should be
established as close as possible to the AD9838.
Avoid running digital lines under the device; these lines couple
noise onto the die. The analog ground plane should be allowed
to run under the AD9838 to avoid noise coupling. The power
supply lines to the AD9838 should use as large a track as possible
to provide low impedance paths and reduce the effects of glitches
on the power supply line. Fast switching signals, such as clocks,
should be shielded with digital ground to avoid radiating noise
to other sections of the board.
Avoid crossover of digital and analog signals. Traces on opposite
sides of the board should run at right angles to each other to
reduce the effects of feedthrough through the board. A micro-
strip technique is by far the best but is not always possible with
a double-sided board. In this technique, the component side of
the board is dedicated to ground planes and signals are placed
on the other side.
Good decoupling is important. The analog and digital supplies
to the AD9838 are independent and separately pinned out to
minimize coupling between the analog and digital sections of the
device. All analog and digital supplies should be decoupled to
AGND and DGND, respectively, with 0.1 μF ceramic capacitors
in parallel with 10 μF tantalum capacitors. To achieve the best
performance from the decoupling capacitors, they should be
placed as close as possible to the device, ideally right up against
the device.
In systems where a common supply is used to drive both the
AVDD and DVDD pins of the AD9838, it is recommended that
the system’s AVDD supply be used. This supply should have the
recommended analog supply decoupling between the AVDD
pin of the AD9838 and AGND, as well as the recommended
digital supply decoupling capacitors between the DVDD pin
and DGND.
Proper operation of the comparator requires good layout strategy.
The layout must minimize the parasitic capacitance between VIN
and the SIGN BIT OUT pin by using a ground plane to add
isolation. For example, in a multilayered board, the VIN signal
can be connected to the top layer, and the SIGN BIT OUT pin
can be connected to the bottom layer. In this way, isolation is
provided by the power and ground planes between VIN and the
SIGN BIT OUT pin.
INTERFACING TO MICROPROCESSORS
The AD9838 has a standard serial interface that allows the part to
interface directly with several microprocessors. The device uses
an external serial clock to write the data or control information
into the device. The serial clock can have a frequency of 40 MHz
maximum. The serial clock can be continuous, or it can idle high
or low between write operations. When data or control informa-
tion is written to the AD9838, FSYNC is taken low and is held
low until the 16 bits of data are written into the AD9838. The
FSYNC signal frames the 16 bits of information that are loaded
into the AD9838.
相關PDF資料
PDF描述
AD9837BCPZ-RL IC WAVEFORM GEN PROG 10LFCSP
VE-2WM-IY-F2 CONVERTER MOD DC/DC 10V 50W
AD9837ACPZ-RL IC WAVEFORM GEN PROG 10LFCSP
VE-2W3-IY-F4 CONVERTER MOD DC/DC 24V 50W
VE-2W2-IY-F3 CONVERTER MOD DC/DC 15V 50W
相關代理商/技術參數
參數描述
AD9838ACPZ-RL7 功能描述:IC DDS 16MHZ LOW PWR 20LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率(位):10 b 主 fclk:25MHz 調節字寬(位):32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AD9838BCPZ-RL 功能描述:IC DDS 16MHZ LOW PWR 20LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率(位):10 b 主 fclk:25MHz 調節字寬(位):32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AD9838BCPZ-RL7 功能描述:IC DDS 16MHZ LP 20LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率(位):10 b 主 fclk:25MHz 調節字寬(位):32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AD9840 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 10-Bit 40 MSPS CCD Signal Processor
AD9840A 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 10-Bit 40 MSPS CCD Signal Processor