- 您現在的位置：買賣IC網 > PDF目錄5875 > ADA4897-2ARMZ-R7 (Analog Devices Inc)IC OPAMP RR 230MHZ LP 10MSOP PDF資料下載
參數資料
| 型號： | ADA4897-2ARMZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/29頁 |
| 文件大小： | 0K |
| 描述： | IC OPAMP RR 230MHZ LP 10MSOP |
| 標準包裝： | 1,000 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 120 V/µs |
| -3db帶寬： | 230MHz |
| 電流 - 輸入偏壓： | 11µA |
| 電壓 - 輸入偏移： | 28µV |
| 電流 - 電源： | 3mA |
| 電流 - 輸出 / 通道： | 80mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 10 V，±1.5 V ~ 5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Data Sheet
ADA4896-2/ADA4897-1/ADA4897-2
Rev.
| Page 17 of 28
THEORY OF OPERATION
AMPLIFIER DESCRIPTION
noise amplifiers that consume 3 mA from supplies ranging from
3 V to 10 V. Fabricated on the Analog Devices SiGe bipolar process,
excess of 200 MHz. The amplifiers are unity-gain stable, and the
input structure results in an extremely low input 1/f noise for a
high speed amplifier.
The rail-to-rail output stage is designed to drive the heavy feed-
back load required to achieve an overall low output referred noise.
To meet more demanding system requirements, the large signal
increased beyond the typical fundamental limits of other low noise,
unity-gain stable amplifiers. The maximum offset voltage of 500 μV
and drift of 0.2 μV/°C make the ADA4896-2/ADA4897-1/
ADA4897-2 excellent amplifier choices even when the low noise
performance is not needed because there is minimal power
penalty in achieving the low input noise or the high bandwidth.
INPUT PROTECTION
from ESD events, withstanding human body model ESD events
of 2.5 kV and charged-device model events of 1 kV with no mea-
sured performance degradation. The precision input is protected
with an ESD network between the power supplies and diode
clamps across the input device pair, as shown in Figure 44.
+IN
ESD
–VS
+VS
BIAS
TO THE REST OF THE AMPLIFIER
–IN
ESD
09
44
7-
06
8
Figure 44. Input Stage and Protection Diodes
For differential voltages above approximately 0.7 V, the diode
clamps begin to conduct. Too much current can cause damage
due to excessive heating. If large differential voltages must be
sustained across the input terminals, it is recommended that the
current through the input clamps be limited to less than 10 mA.
Series input resistors that are sized appropriately for the expected
differential overvoltage provide the needed protection.
The ESD clamps begin to conduct for input voltages that are
more than 0.7 V above the positive supply and input voltages
more than 0.7 V below the negative supply. If an overvoltage
condition is expected, it is recommended that the input current
be limited to less than 10 mA.
DISABLE OPERATION
circuitry. If the DISABLE pin is left unconnected, the base of
the input PNP transistor is pulled high through the internal
pull-up resistor to the positive supply and the part is turned
on. Pulling the DISABLE pin to ≥2 V below the positive supply
turns the part off, reducing the supply current to approximately
18 μA for a 5 V voltage supply.
+VS
–VS
DISABLE
ESD
IBIAS
TO
AMPLIFIER
BIAS
09
44
7-
03
7
Figure 45. DISABLE Circuit
The DISABLE pin is protected by ESD clamps, as shown in
Figure 45. Voltages beyond the power supplies cause these
diodes to conduct. For protection of the DISABLE pin, the
voltage to this pin should not exceed 0.7 V above the positive
supply or 0.7 V below the negative supply. If an overvoltage
condition is expected, it is recommended that the input current
be limited with a series resistor to less than 10 mA.
When the amplifier is disabled, its output goes to a high
impedance state. The output impedance decreases as frequency
increases; this effect can be observed in Figure 36. In disable
mode, a forward isolation of 50 dB can be achieved at 10 MHz.
Figure 43 shows the forward isolation vs. frequency data.
B
相關PDF資料 |
PDF描述 |
|---|---|
| 77313-101-20LF | HDR STR DR.100 DP |
| TSW-202-07-G-S | CONN HEADER 2POS .200" SNGL |
| TSW-105-20-T-S | CONN HEADER 5POS .100" SNGL |
| TSM-102-01-T-SH-P-TR | CONN HEADER 2POS .100" SNGL SMD |
| 9-146309-0-32 | CONN HEADR BRKWAY .100 64POS R/A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADA4897-2ARMZ-RL | 功能描述:IC OPAMP RR 230MHZ LP 10MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:73 系列:Over-The-Top® 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.07 V/µs 增益帶寬積:200kHz -3db帶寬:- 電流 - 輸入偏壓:1nA 電壓 - 輸入偏移:285µV 電流 - 電源:50µA 電流 - 輸出 / 通道:25mA 電壓 - 電源，單路/雙路(±):2 V ~ 44 V，±1 V ~ 22 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WFDFN 裸露焊盤 供應商設備封裝:16-DFN-EP（5x3） 包裝:管件 |
| ADA4897-2TRMZ-EP | 制造商:Analog Devices 功能描述:LOW NOISE LOW POWER R/R OP AMP DUAL - Rail/Tube 制造商:Analog Devices 功能描述:IC OPAMP GP 230MHZ RRO 10MSOP 制造商:Analog Devices 功能描述:Low Noise Low Power R/R Op Amp Dual |
| ADA4898-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Voltage, Low Noise, Low Distortion, Unity Gain Stable, High Speed Op Amp |
| ADA4898-1YRD-EBZ | 制造商:Analog Devices 功能描述:HIGH VOLTAGE, LOW NOISE, LOW DISTORTION, UNITY-GAIN STABLE, - Boxed Product (Development Kits) |
| ADA4898-1YRDZ | 功能描述:IC OPAMP VF ULN ULDIST 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
發布緊急采購，3分鐘左右您將得到回復。