- 您現在的位置：買賣IC網 > PDF目錄8611 > ADA4938-1ACPZ-RL (Analog Devices Inc)IC ADC DRIVER DIFF 16-LFCSP PDF資料下載
參數資料
| 型號： | ADA4938-1ACPZ-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC DRIVER DIFF 16-LFCSP |
| 標準包裝： | 5,000 |
| 類型： | ADC 驅動器 |
| 應用： | 數據采集 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 16-LFCSP-VQ |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ADA4938-1/ADA4938-2
Rev. A | Page 19 of 28
THEORY OF OPERATION
The ADA4938-x differs from conventional op amps in that it
has two outputs whose voltages move in opposite directions.
Like an op amp, it relies on open-loop gain and negative
feedback to force these outputs to the desired voltages. The
ADA4938-x behaves much like a standard voltage feedback op
amp and makes it easier to perform single-ended-to-differential
conversions, common-mode level shifting, and amplifications of
differential signals. Also like an op amp, the ADA4938-x has
high input impedance and low output impedance.
Two feedback loops are employed to control the differential and
common-mode output voltages. The differential feedback, set
with external resistors, controls only the differential output
voltage. The common-mode feedback controls only the common-
mode output voltage. This architecture makes it easy to set the
output common-mode level to any arbitrary value. It is forced,
by internal common-mode feedback, to be equal to the voltage
applied to the VOCM input, without affecting the differential
output voltage.
The ADA4938-x architecture results in outputs that are highly
balanced over a wide frequency range without requiring tightly
matched external components. The common-mode feedback
loop forces the signal component of the output common-
mode voltage to zero, which results in nearly perfectly balanced
differential outputs that are identical in amplitude and are
exactly 180° apart in phase.
ANALYZING AN APPLICATION CIRCUIT
The ADA4938-x uses open-loop gain and negative feedback to
force its differential and common-mode output voltages in such
a way as to minimize the differential and common-mode error
voltages. The differential error voltage is defined as the voltage
between the differential inputs labeled +IN and IN (see
Figure 57). For most purposes, this voltage can be assumed
to be zero. Similarly, the difference between the actual output
common-mode voltage and the voltage applied to VOCM can also
be assumed to be zero. Starting from these two assumptions,
any application circuit can be analyzed.
SETTING THE CLOSED-LOOP GAIN
The differential-mode gain of the circuit in Figure 57 can be
determined by
G
F
dm
IN
dm
OUT
R
V
=
,
This assumes the input resistors (RG) and feedback resistors (RF)
on each side are equal.
ESTIMATING THE OUTPUT NOISE VOLTAGE
The differential output noise of the ADA4938 can be estimated
using the noise model in Figure 58. The input-referred noise
voltage density, vnIN, is modeled as a differential input, and the
noise currents, inIN and inIN+, appear between each input and
ground. The noise currents are assumed to be equal and produce a
voltage across the parallel combination of the gain and feedback
resistances. vn, cm is the noise voltage density at the VOCM pin.
the input noise sources, the multiplication factors, and the output-
referred noise density terms.
ADA4938
+
RF2
VnOD
VnCM
VOCM
VnIN
RF1
RG2
RG1
VnRF1
VnRF2
VnRG1
VnRG2
inIN+
inIN–
06
59
2-
0
05
Figure 58. ADA4938 Noise Model
Table 9. Output Noise Voltage Density Calculations
Input Noise Contribution
Input Noise Term
Input Noise
Voltage Density
Output
Multiplication Factor
Output Noise
Voltage Density Term
Differential Input
vnIN
GN
vnO1 = GN(vnIN)
Inverting Input
inIN
inIN × (RG2||RF2)
GN
vnO2 = GN[inIN × (RG2||RF2)]
Noninverting Input
inIN+
inIN+ × (RG1||RF1)
GN
vnO3 = GN[inIN+ × (RG1||RF1)]
VOCM Input
vn, cm
GN(β1 β2)
vnO4 = GN(β1 β2)(vnCM)
Gain Resistor, RG1
vnRG1
(4kTRG1)1/2
GN(1 β1)
vnO5 = GN(1 β1)(4kTRG1)1/2
Gain Resistor, RG2
vnRG2
(4kTRG2)1/2
GN(1 β2)
vnO6 = GN(1 β2)(4kTRG2)1/2
Feedback Resistor, RF1
vnRF1
(4kTRF1)1/2
1
vnO7 = (4kTRF1)1/2
Feedback Resistor, RF2
vnRF2
(4kTRF2)1/2
1
vnO8 = (4kTRF2)1/2
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2TV-MW-B1 | CONVERTER MOD DC/DC 5.8V 100W |
| AD7398BRU-REEL7 | IC DAC 12BIT QUAD SRL 16-TSSOP |
| ADA4937-1YCPZ-RL | IC ADC DIFF DRIVER 16-LFCSP |
| VE-24N-IV-F1 | CONVERTER MOD DC/DC 18.5V 150W |
| LTC6404IUD-4#TRPBF | IC AMP/DRIVER DIFF 16-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADA4938-1YCP-EBZ | 功能描述:BOARD EVAL FOR ADA4938-1YCP RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| ADA4938-1YCPZ-R2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultra-Low Distortion Differential ADC Driver |
| ADA4938-1YCPZ-R7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultra-Low Distortion Differential ADC Driver |
| ADA4938-1YCPZ-RL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultra-Low Distortion Differential ADC Driver |
| ADA4938-2ACP-EBZ | 功能描述:24-LFCSP Package 2 - Dual Channels per IC Differential Amplifier Evaluation Board 制造商:analog devices inc. 系列:- 零件狀態:過期 每 IC 通道數:2 - 雙 放大器類型:差分 輸出類型:差分 壓擺率:- -3db 帶寬:- 電流 - 輸出/通道:- 工作溫度:- 電流 - 電源（主 IC）:- 電壓 - 電源，單/雙（±）:- 板類型:裸（未填充） 所含物品:板 使用的 IC/零件:24-LFCSP 封裝 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。